Bedienungsanleitung Yamaha ES8 (Seite 289 von 300) (Englisch)

48744

289

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

Installing Optional Hardware

289

Owner’s Manual

Appendix

Optional DIMM Installation

This section explains how to install DIMM memory modules to the MOTIF ES.

Compatible DIMMs

The MOTIF ES does not necessarily support all commercially

available DIMMs. Yamaha cannot guarantee operation of

DIMMs that you purchase. Before purchasing DIMMs, please

consult your Yamaha dealer, or an authorized Yamaha

distributor (see list at end of the Owner’s Manual) for advice,

or see the following page:

http://www.yamahasynth.com/

DIMM Type and DIMM Conﬁguration

•Yamaha recommends that you purchase DIMMs that

conform to the JEDEC* standard. Please be aware,

however, that conformance to this standard does not

constitute a guarantee that the DIMMs will operate correctly

on the MOTIF ES.

* JEDEC (Joint Electron Device Engineering Council) sets standards for

terminal conﬁgurations within electronic devices.

• Use only 168-pin DIMMs of 64, 128 or 256 MB capacity

(synchronized DRAM; PC100 or PC133).

• When installing DIMMs, make sure to install them in a

matched pair of the same capacity. You cannot install only

one module and leave the second memory socket open.

Also make sure each DIMM in the pair is of the same

manufacturer and the same type. DIMMs of different

makers and conﬁgurations may not work together.

•When purchasing DIMMs, make sure that the DIMM design

does not utilize more than 18 memory chips per module.

(DIMMs comprised of more than 18 chips do not operate

correctly on the MOTIF ES.)

DIMM Installation

1~3

Use the same operation as in “Installing the AIEB2.”

4Insert the two DIMMs into the DIMM sockets.

5Re-install the cover you removed in step #3, in reverse

order (page 285).

Check that the installed DIMMs are functioning properly.

Set the MOTIF ES right-side up, and connect the power

cord to the rear-panel AC INLET jack and an AC outlet. Turn

on the power, go to the SAMPLING display by pressing the

[INTEGRATED SAMPLING] button, and press the

[INFORMATION] button (page 276). If the DIMMs have

been installed properly, the appropriate available memory

size is indicated in the display.

nIf the DIMMs have not been installed properly, the MOTIF ES may

freeze when you press the [INTEGRATED SAMPLING] button. If

this occurs, turn the power off, perform the instructions above

again, and make sure to install the DIMMs ﬁrmly in step #4.

Removing DIMMs

64MB x 2 = 128MB 128MB x 2 = 256MB

256MB x 2 = 512MB

168-pin DIMMs

Notch for alignment

Ejector

lever

Location for DIMM installation

DIMM sockets

Underside of the MOTIF ES

Installing the DIMM modules to the sockets

Make sure that the DIMM module is

aligned correctly before you install it.

Insert the DIMM vertically

in the socket. Press it in ﬁrmly until it

“snaps” or locks in place.

↓ Rear panel

Press the ejector lever

until the DIMM unlocks. Pull the DIMM vertically

out of the socket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha ES8 Seite 289

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha ES8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info