Bedienungsanleitung Yamaha EX5 (Seite 170 von 304) (Englisch)

48736

170

Zoom out

Zoom in

Vorherige Seite

1/304

Nächste Seite

Performance Mode

170

[F8]: PRE (Preset)

Settings related to the preset values and MIDI matters

applied to the tone generator for each part.

■ Part

■ Bank (Voice Bank)

■ Number

These parameters are the same as those explained in

the MIX screen. See page 164.

Bank/PC:MD (Bank/Program Change: MIDI)

Sets the program change and bank select messages that

are sent to an external MIDI device when making

bank/program changes on the front panel of the

EX5/5R/7. A different value can be set for each part.

■ PC To MIDI

Sets whether or not the program change and bank

select messages are sent to an external MIDI device.

When set to “on” messages are sent, and when set to

“off” messages are not sent.

❏ Settings: off, on

■ MD BankMSB (MIDI Bank Select MSB)

Sets the bank select MSB messages that are sent to

an external MIDI device when making

bank/program changes.

❏ Settings: 000~127

■ MD BankLSB (MIDI Bank Select LSB)

Sets the bank select LSB messages that are sent to an

external MIDI device when making bank/program

changes.

❏ Settings: 000~127

Bank Select messages are MIDI messages used to

change a voice bank. With the combination of the two

Bank Select MSB and LSB control change messages, a

single voice bank can be specified. Available banks and

control change numbers will differ depending on the

tone generator that is used. For more information, refer

to the Owner’s Manual for each tone generator that is

in use.

■ MIDI PC (MIDI Program Change)

Sets the MIDI program numbers sent to an external

MIDI device when making bank/program changes.

❏ Settings: 001~128

Note that the program numbers are 001~128, but the

actual MIDI program change numbers range from

0~127. Therefore, keep in mind that the numbers are

shifted by one.

Controller

■ InitVal PB (Initial Value Pitch Bend)

Sets the preset value for the pitch bend for a part.

❏ Settings: 0~127

■ Ctrl To TG (Controller To Tone Generator)

When making bank/program changes, this sets

whether or not the preset values for the six

controllers below (AT, FC, BC, RC, MW1, MW2) are

sent to the internal tone generator. When set to “on”

they are sent, and when set to “off” they are not

sent.

❏ Settings: off, on

■ Ctrl To MIDI (Controller To MIDI)

When making bank/program changes, this sets

whether or not the preset values for the six

controllers below (AT, FC, BC, RC, MW1, MW2) are

sent to an external MIDI device. When set to “on”

they are sent, and when set to “off” they are not

sent.

❏ Settings: off, on

■ InitVal MW1/MW2/AT/FC/BC/RB (Initial

Values)

Sets the control change preset values that are sent by

each controller.

❏ Settings: Each of the following devices can be set from

0~127: AT (After Touch), FC (Foot Controller),

BC (Breath Controller), RB (Ribbon Controller),

MW1 (Modulation Wheel 1), MW2 (Modulation

Wheel 2)

Performance/E/qx 5/21/98 11:35 AM Page 170

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha EX5 Seite 170

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha EX5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info