Bedienungsanleitung Yamaha EX5 (Seite 218 von 304) (Englisch)

48736

218

Zoom out

Zoom in

Vorherige Seite

1/304

Nächste Seite

218

Song Mode

❏ Settings: –99~+0~+99

8. Shift Event

This job replaces all occurrences of a specific event

type (within the designated range of the specified

sequence track) with some other designated event type.

For example, you can use this function to change

breath controller data into channel aftertouch events.

■ Track

Sets the track where Shift Event will be executed.

❏ Settings: 1~16(Sequence tracks 1~16)

■ Measure

Sets the measure range (beginning measure to the

end measure) where Shift Event is executed.

❏ Settings: 001~999 (for the beginning measure and the

end measure)

■ Src Event (Source Event)

Selects the source that will be changed.

❏ Settings: Control Change, Ch After Touch (Channel After

Touch), Pitch Bend, Note (Note#: note

numbers), Note (Vel: velocity values of each

note)

Original Data

(Vel)

64 64 6464 64

64 54 44 2434 14

94 114

Range=+40(001: 1~003: 1)

64 74 84 104

Range=–40(001: 1~003: 1)

■ Dst Event (Destination Event)

Sets the destination event that the source event is

changed to.

❏ Settings: Control Change, Ch After Touch (Channel After

Touch), Pitch Bend, Note (Note#: the data

change of the source event will be replaced with

note numbers with the fixed velocity 64 and

fixed gate time 108), Note (Vel: the data change

of the source event will be replaced with

velocities with the fixed pitch C3 and fixed gate

time 108).

[F7]: UNDO/REDO

Undo/Redo function is assigned to [F7]. Undo cancels

the changes you made in your most recent record, edit,

or job operation, restoring the data to its previous state.

Redo, which becomes available only after you execute

an Undo, cancels Undo operation and restores the

changes. When you inadvertently execute a job, make a

mistake while recording or editing, this job is

convenient for restoring important data that would

otherwise be lost.

Undo/Redo is always effective after a record, edit, and

job operation. As soon as you execute an Undo, the job

name changes to REDO. UNDO and REDO alternately

appear after Undo/Redo operation. If data is not

changed, Undo/Redo will not become effective.

Steps for Executing Undo/Redo

1 Press [F7] (UNDO/REDO and the UNDO/REDO

screen will be displayed.

UNDO/REDO:

Available operation, UNDO or REDO, is displayed.

The target of Undo/Redo:

The target of Undo/Redo function will be displayed, that is,

the most recent record, edit, or job operation name.

2 Press [ENTER] to execute Undo/Redo. “Completed!”

will appear in the screen indicating that the

cancellation was executed and the previous screen

will be displayed.

If [F7] (UNDO) is pressed without any previous operation

taking place, “Undefined job” will be displayed and Undo

cannot executed.

UNDO/REDO The target of Undo/Redo

Song/E/qx 5/21/98 11:41 AM Page 218

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha EX5 Seite 218

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha EX5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info