Bedienungsanleitung Yamaha GX-505RDS (Seite 45 von 48) (Englisch)

557527

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

E-37

English

Appendix

Troubleshooting

Refer to the chart below when this system does not function properly. If the problem you are experiencing is not listed

below or if the instruction below does not help, disconnect the supply lead and contact your authorized YAMAHA dealer or

service center.

Problem

This system does not work

normally.

The sound suddenly goes off.

No sound from speakers.

No sound from the external

unit connected to this system.

Timer cannot be set.

This system will not operate

properly.

The volume level cannot be

increased, or sound is

distorted.

Excessive static in FM

broadcasts.

Noise increases during stereo

broadcasts.

Stereo broadcasts are noisy

and STEREO indicator blinks

on and off.

Preset stations cannot be

selected.

Buzzing or static during AM

broadcasts.

AM broadcast sensitivity is

poor.

Cause

There is an influence of strong external

noise (lightning, excessive static electricity,

etc.) or the system was operated incorrectly.

The protection circuit was activated because

of a short circuit, etc.

The SLEEP timer was activated.

Speaker connections are not secure.

Incorrect cord connections.

Input source selection is not correct.

Current time is not set.

The internal microcomputer has been frozen

by an external electric shock (lightning,

excessive static electricity, etc.) or power

supply with low voltage.

The component connected to the AUX/MD

terminals on the rear of the main unit is

turned off.

Interference from starting motor of nearby

car.

Interference from thermostat of nearby

electric appliance.

Antenna input is too weak due to

obstructions or excessive distance from

broadcasting station.

Insufficient antenna input.

Preset memory has been erased.

Interference from sources such as lightning,

fluorescent lights, electric motors or

thermostat of nearby electric appliance.

TV or this system is being used nearby.

Radio signal is weak or antenna is not

properly connected.

What to Do

Set this system to the standby mode and disconnect the

AC supply lead from the AC outlet. After about 30

seconds, connect the power and operate this system

again.

Set this system to the standby mode, then turn on to

reset the protection circuit.

Cancel the SLEEP timer function.

Secure the connections.

Connect the cords properly. If the problem persists, the

cords may be defective.

Make a correct input source selection.

Set current time.

Unplug the AC supply lead from the wall AC outlet,

then plug in again after about one minute.

Turn on the power to the component.

Position the FM antenna as high and as far away from

nearby roads as possible. Use coaxial cable.

Check antenna connections.

Install a multi-element type FM antenna if possible.

Install an antenna suited for the electric field strength

of your area.

Reprogram memory presettings.

Problem is difficult to eliminate but can be lessened by

grounding AM loop antenna.

Move away from TV or this system.

Properly connect AM loop antenna.

Change orientation of AM loop antenna.

Install an external AM antenna.

General

Tuner

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha GX-505RDS Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info