Bedienungsanleitung Yamaha HTR-5063 (Seite 73 von 84) (Englisch)

652589

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

En 73

APPENDIX

Troubleshooting

No sound is heard

from the surround

speakers.

This unit is in straight decoding

mode and a monaural source is

being played back.

Press STRAIGHT to exit straight decoding

mode.

Sound may not be output from

certain channels depending on

input sources or sound field

programs.

Try another sound field program. 30

No sound is heard

from the surround

back speakers.

“Extended Surround” in the

Option menu is set to “Off,” or an

input signal does not contain a

surround back flag with “Extended

Surround” set to “Auto.”

Set “Extended Surround” other than “Off”

or “Auto.”

No sound is heard

from the subwoofer.

A subwoofer is not connected, or it

is inactive.

Check that a subwoofer is connected

correctly, and from the Setup menu

“Subwoofer” (“Speaker Setup” → “Config”

→ “Subwoofer”), set the subwoofer to

“On.”

The subwoofer is turned off. Turn the subwoofer power on.

If the subwoofer includes an Auto Power

Off function, then lower the Auto Power Off

sensitivity settings.

—

The source does not contain LFE

(☞p. 78) or low frequency signals.

—

The right

combination of audio

/ video jacks to

connect cannot be

found.

Combine input connected to the

external component video output

with another input audio jack.

Display the Input Audio menu for the

connected video output, select “Audio In,”

and select the jack to use for audio input.

The audio input

sources cannot be

played in the desired

digital audio signal

format.

The connected component is not

set to output the desired digital

audio signals.

Set the playback component properly

referring to its instruction manual.

—

There is noise

interference from

digital or radio

frequency

equipment.

This unit is too close to other

digital or radio frequency

equipment.

Move this unit further away from such

equipment.

—

Problem Cause Remedy

See

page

Noise/hum noise is

heard.

Incorrect cable connection.

Connect the audio cables properly.

If the problem persists, the cables may be

defective.

—

A DTS-CD is being played back. 1) When only noise is output

If a DTS bitstream signal is not properly

input to this unit, only noise is output.

Connect the playback component to this

unit by digital connection and playback the

DTS-CD. If the condition is not improved,

the problem may results from the playback

component. Consult the manufacturer of the

playback component.

2) When noise is output during playback or

skip operation

Before playing back the DTS-CD, display

the Option menu after selecting the input

source and set “Decoder Mode” to “DTS.”

—

The volume cannot

be increased, or the

sound is distorted.

The component connected to the

output jacks of this unit is not

turned on.

When the component connected to the

output jacks of this unit is not turned on, the

sound may be distorted, or the volume may

decreased due to the nature of AV receivers.

Turn on all components connected to this

unit.

—

“Max Volume” is set to a low

value.

Set it to a higher value. 55

Problem Cause Remedy

See

page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha HTR-5063 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info