Bedienungsanleitung Yamaha HTR-5230RDS (Seite 29 von 50) (Englisch)

549948

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

Automatic Preset Tuning (for RDS

stations only)

You can make use of the automatic preset tuning function

for RDS stations only. This function enables the unit to

automatically tune in with strong signals and to sequentially

store up to 40 RDS stations (5 groups x 8 stations). (Refer to

pages 30 to 32 for details on RDS stations.)

1 Press FM/AM to select the FM band.

2 Press TUNING MODE so that the “AUTO”

indicator lights up on the display.

3 Hold down MEMORY for about three seconds.

The preset number, the “MEMORY” and “AUTO”

indicators flash. After about five seconds, automatic

preset tuning begins from the frequency currently

displayed toward the higher frequencies.

Received stations are sequentially stored as A1, A2 ...

A8. If more than 8 stations have been tuned, they are

stored as preset station numbers in other groups (B, C,

D and E) in that order.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost when this unit is set in the standby mode.

If, however, the power cord is disconnected from the AC

power outlet or the power is cut for more than one week,

the memory will be erased. If so, store the stations again

by using preset tuning methods.

–+–+

21 3

■ Automatic preset tuning options

You can select the preset number from which the unit will

store RDS stations and/or begin tuning toward lower

frequencies. Before automatic preset tuning begins (after

pressing MEMORY in step 3),

1. Press A/B/C/D/E and PRESET/TUNING to select the

preset number with which the first station will be stored.

The automatic preset tuning will stop when stations have

all been stored up to E8.

2. Press PRESET/TUNING (EDIT) to turn “ z ” off and

then press PRESET/TUNING l to begin tuning toward

lower frequencies.

■ When automatic preset tuning is

completed

The display shows the frequency of the last preset station.

Check the contents and the number of preset stations by

following the procedure in the section “To Recall a Preset

Station” on page 28.

Notes

• A new setting can be stored in place of the former one.

• You can manually replace a preset station with another FM or AM

station by simply using the manual preset tuning method.

• Automatic preset tuning will be performed for all RDS network

stations until all have been stored up to E8. Even if the number of

received stations is not enough to be stored up to E8, automatic

preset tuning is automatically ended after searching for all

stations.

• Only RDS stations with sufficient signal strength are stored by

automatic preset tuning. If the station you want to store is weak in

signal strength, tune in to it manually in monaural mode and store

it by using the manual preset tuning method. (There may be a

case that this unit cannot receive a station which could be

received by using the automatic tuning method. This is because

this unit receives a large amount of PI (Program Identification)

data along with the station.)

TUNING

Lights up

Flashes

0106V396RDS26-29_EN 1/18/0, 3:11 PM27

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha HTR-5230RDS Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info