Bedienungsanleitung Yamaha HTR-5440RDS (Seite 25 von 57) (Englisch)

549950

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

English

BASIC OPERATION

ADVANCED OPERA

TION

APPENDIX

INTRODUCTION

PREPARATION

■ Notes on playing a source

encoded with a DTS signal

• If the digital output data of the player has been processed

in any way, you may not be able to perform DTS

decoding even if you make a digital connection between

this unit and the player.

• If you play a source encoded with a DTS signal and set

the input mode to ANALOG, this unit reproduces the

noise of an unprocessed DTS signal. When you want to

play a DTS source, be sure to connect the source to a

digital input jack and set the input mode to AUTO or

DTS.

• If you switch the input mode to ANALOG while playing

a source encoded with a DTS signal, this unit reproduces

no sound.

• The following phenomena may occur if the input mode

is set to AUTO when playing back a source encoded with

DTS:

– If you continue to play a source encoded with a DTS

signal, this unit automatically switches to the “DTS-

decoding” mode to prevent noise from being generated

during subsequent operation. (The “t” indicator

lights up on the display.) The “t” indicator may flash

immediately after playback of a source encoded with a

DTS signal has finished. Only a source encoded with a

DTS signal can be played back while this indicator is

flashing. (The indicator will flash for less than a minute.)

If you want to play a normal PCM source soon, set the

input mode back to AUTO.

– The “t” indicator may flash when a search or skip

operation is performed. If this status continues for a

certain length of time, the unit will automatically switch

from the “DTS-decoding” mode to PCM digital signal

input mode and the “t” indicator will go out.

Input Modes and Indications

This unit comes with various input jacks. If your component

is connected to more than one type of input jack, you can set

the priority of the input signal.

Press INPUT MODE (or the input selector

button that you have pressed to select the

input source on the remote control) repeatedly

until the desired input mode is shown on the

display.

PLAYING A SOURCE

AUTO: In this mode, the input signal is

automatically selected in the following

order:

1) Dolby Digital or DTS signal

2) Digital (PCM) signal

3) Analog signal

DTS: In this mode, only the digital input

signal encoded with DTS is selected

even if another signal is input at the

same time.

ANALOG (ANLG): In this mode, only the analog input

signal is selected even if a digital

signal is input at the same time.

Notes

• If digital signals are input from both the COAXIAL and

OPTICAL jacks, the digital signal from the COAXIAL jack is

selected.

• When AUTO is selected, this unit automatically determines the

type of signal. If this unit detects a Dolby Digital or DTS signal,

the decoder automatically switches to the appropriate setting and

reproduces 5.1 channel source.

• The sound output may be interrupted for some LD players and

DVD players in the following situation:

When the input mode has been set to AUTO and a search is

performed while playing the source encoded with a Dolby Digital

or DTS signal, the sound may delay for a moment when playback

is resumed.

• Depending on the LD player, playback may not be made when

playing an LD that is not digitally recorded with the input mode

set to AUTO. If this happens, set the input mode to ANALOG.

Front panel

Remote control

Input mode

INPUT MODE

0104V420RDS21-25_EN 2/12/1, 1:35 PM23

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha HTR-5440RDS Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info