Bedienungsanleitung Yamaha HTR-5790 (Seite 29 von 90) (Englisch)

652608

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

AUTO SETUP

PREPARATION

For best results, make sure the room is as quiet as possible

during the auto setup procedure. If there is too much

ambient noise, the results may not be satisfactory.

If your subwoofer can adjust the output volume and the crossover

frequency, set the volume to about half way (or slightly less) and

set the crossover frequency to the maximum.

1 Switch on the receiver and video monitor.

Make sure the OSD is displayed.

2 Press AMP to select the AMP mode, then

press SET MENU to enter the SET MENU.

3 Press u / d to select AUTO SETUP, then

press i once to enter the main menu.

4 Press u / d repeatedly to select WIRING,

DISTANCE, SIZE, EQUALIZING or LEVEL.

5 When WIRING, DISTANCE, SIZE or LEVEL is

selected, press j / i to select:

CHECK

To automatically check and adjust the selected

item.

SKIP To skip the selected item and perform no

adjustments.

When using THX speakers, set SIZE to SKIP and make sure

that SMALL or SMLx2 is selected in SPEAKER SET

(page 49) and that 80Hz is selected in CROSS OVER

(page 50).

When EQUALIZING is selected, press j / i to

select:

FRONT To adjust the frequency response of

each speaker in accordance with the

sound of your front speakers.

Recommended if your front speakers

are of much higher quality than your

other speakers.

FLAT To average the frequency response of

all speakers. Recommended if all of

your speakers are of similar quality.

LOW To average the frequency response of

all speakers, giving priority to the

accuracy of bass frequencies.

MID To average the frequency response of

all speakers, giving priority to the

accuracy of mid-range frequencies.

HIGH To average the frequency response of

all speakers, giving priority to the

accuracy of high frequencies.

SKIP To skip the selected item and perform

no adjustments.

6 Press d to select SETUP, then press j / i to

select:

AUTO To automatically perform the entire

auto setup procedure.

STEP To pause for confirmation between

each check in the auto setup procedure.

RELOAD To restore the last auto setup setting.

7 Press d to select START PUSH +, then press

Loud test tones will be output from each speaker and

WAIT appears during the auto setup procedure.

If E-10:OTHER ERROR appears during testing, restart the

procedure from step 3.

Starting the setup

SET MENU

A/B/C/D/E

AMP

then

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–



SET MENU

. ;AUTO SETUP

;MANUAL SETUP

: Up/Down

: Select

-/+

AUTO:MENU

.WIRING;;;;;CHECK

DISTANCE;;;CHECK

SIZE;;;;;;;CHECK

EQUALIZING;;FLAT

LEVEL;;;;;;CHECK

SETUP;;;;;;;AUTO

START PUSH +

: Up/Down

: Select

-/+

Note

00_HTR-5790U_EN.book Page 25 Tuesday, December 9, 2003 9:16 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha HTR-5790 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info