Bedienungsanleitung Yamaha HTR-6230 (Seite 20 von 196) (Italienisch, Spanisch)

516960

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

16 En

This unit has the Yamaha Parametric Acoustic Optimizer (YPAO). With the YPAO, this unit automatically adjusts output

characteristics of your speakers based on speaker positions, speaker performances, and acoustic characteristics of the

room. We recommend that you first adjust the output characteristics with the YPAO when you use this unit.

• Initial settings are indicated by (*) in the following each parameter.

1 Make sure of the following check points.

Before starting the automatic setup, check the

following check points.

• All speakers and subwoofer are connected

appropriately.

• Headphones are disconnected from this unit.

• This unit is turned on.

• The connected subwoofer is tuned on and the

volume level is set to about half way (or slightly

less).

• FRONT A speakers are selected as the front

speaker system (see page 19).

• The room is sufficiently quiet.

• The crossover frequency control of the connected

subwoofer is set to the maximum.

2 Connect the supplied optimizer microphone

to the OPTIMIZER MIC jack on the front

panel.

“SETUP•••••AUTO” appears on the front panel

display.

3 Place the optimizer microphone at your

normal listening position on a flat level

surface with the omni-directional

microphone heading upward.

• We recommend that you use a tripod (etc.) to affix the optimizer

microphone at the same height as your ears would be when you are

seated in your listening position. You can use the attached screw of

a tripod (etc.) to fix the optimizer microphone to the tripod (etc.).

4 Press ol / h to select “AUTO.”

Note

• “RELOAD” or “UNDO” is available only when you have

previously run “AUTO SETUP” and confirmed the results.

5 Press oENTER to start the setup

procedure.

This unit starts the automatic setup procedure. Loud

test tones are output from each speaker during the

audio setup procedure. After all settings

(“INITIALIZING,” “WIRING/LEVEL,”

“DISTANCE,” “SIZE”) are sequentially completed,

“FINISH” appears on the front panel display.

• To cancel the automatic setup, press ok.

Optimizing the speaker setting for your listening room (YPAO)

Notes

• Be advised that it is normal for loud test tones to be

output during the “AUTO SETUP” procedure. Do not

allow small children to enter the room during the

procedure.

• To achieve the best results, make sure that the room

is as quiet as possible while the “AUTO SETUP”

procedure is in progress. If there is too much ambient

noise, the results may not be satisfactory.

Using AUTO SETUP

VOLUME

MIN

MAX

MIN MAX

CROSSOVER

HIGH CUT

Controls of a subwoofer (example)

Choice Function

AUTO* Automatically runs the entire “AUTO

SETUP” procedure.

RELOAD Reloads the last “AUTO SETUP” settings and

overrides the previous settings.

UNDO Undoes the last “AUTO SETUP” settings and

restores the previous settings.

DEFAULT Resets the “AUTO SETUP” parameters to the

initial factory settings.

Optimizer microphone

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha HTR-6230 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha HTR-6230

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info