Bedienungsanleitung Yamaha HTR-6230 (Seite 44 von 196) (Italienisch, Spanisch)

516960

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

40 En

Troubleshooting

■ Tuner

This unit does not

operate properly.

The internal microcomputer has been

frozen by an external electric shock (such

as lightning or excessive static electricity)

or by a power supply with low voltage.

Disconnect the power cable from the AC wall outlet

and then plug it in again after about 30 seconds.

—

“CHECK SP WIRES”

appears on the front

panel display.

Speaker cables are short-circuited. Make sure all speaker cables are connected correctly. 9

There is noise

interference from

digital or radio

frequency equipment.

This unit is too close to the digital or high-

frequency equipment.

Move this unit further away from such equipment. —

The picture is

disturbed.

The video source uses scrambled or

encoded signals to prevent dubbing.

This unit suddenly

enters the standby

mode.

The internal temperature is too high and

the overheat protection circuitry has been

activated.

Wait about 1 hour for this unit to cool down and then

turn it back on.

—

Virtual CINEMA DSP

is not activated.

“MULTI CH” is selected as the input

source.

Select an input source other than “MULTI CH.” 18

Headphones are connected to the

PHONES jack.

Disconnect the headphone plug from the PHONES

jack.

—

This unit is in the “5ch Stereo” mode. Exit from the “5ch Stereo” mode. 25

SILENT CINEMA is

not activated.

“MULTI CH” is selected as the input

source.

Select an input source other than “MULTI CH.” 18

The unit is in the “2ch Stereo,”

“STRAIGHT” or “Music Enh.2ch” mode.

Exit from the “2ch Stereo,” “STRAIGHT” or “Music

Enh2ch” mode.

Problem Cause Remedy

See

page

FM stereo reception is

noisy.

The characteristics of FM stereo

broadcasts may cause this problem

when the transmitter is too far away or

the antenna input is poor.

Check the antenna connections. 15

Try using a high-quality directional FM

antenna.

—

Use the manual tuning method. 27

There is distortion, and

clear reception cannot

be obtained even with a

good FM antenna.

There is multi-path interference. Adjust the antenna position to eliminate

multi-path interference.

—

The desired station

cannot be tuned into

with the automatic

tuning method.

The signal is too weak. Use a high-quality directional FM antenna. —

Use the manual tuning method. 27

Previously preset

stations can no longer

be tuned into.

This unit has been disconnected for a

long period.

Set preset stations. 27

“...WAIT” or “CT WAIT”

appears on the front

panel

The signal strength is weakened while

this unit is receiving the Radio Data

System data.

Check the antenna connections. 15

Try using a high-quality directional FM

antenna.

—

Use the manual tuning method. 27

Problem Cause Remedy

See

page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha HTR-6230 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha HTR-6230

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info