Bedienungsanleitung Yamaha KX10 (Seite 9 von 16) (Englisch)

29781

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

B/ C/MPX FILTER indicators

Display during recording

–30 20 15 10 8 6 4 0 2

SOURCE

REC

TAPE

TAPE TUNING

I/NORM II/HIGH IV/METAL

MPX FILTER

B C

Peak level meters

TAPE TUNING indicator

SOURCE/TAPE indicators

Note:

The tape remain indicator may differ depending on the tape

length, tape type or the size of hub. So, use this indicator as

an aid to recognize the remaining length of the tape to be

played back.

To stop recording temporarily

Press the REC/PAUSE button. To resume recording,

press the 3 PLAY button.

To stop recording and remove the cassette

tape

Press the 7 STOP button and then the ) button. The

cassette tray comes out and you can remove the cassette

tape.

To enter the standby mode

Press the STANDBY/ON switch again.

Three head system

The three-head system allows the just-recorded sound to be

monitored while recording. You can compare the difference

between the recorded sound and the source sound by

switching the monitor mode (SOURCE or TAPE) with the

MONITOR button, so you can try to obtain a recording

sound identical to the source sound.

To monitor the just recorded sound

Setting the recording level (in step 3)

Play the loudest passage of the source to be recorded and

watch the meter readings. When using Normal position

tapes (type I/NORM) or High position tapes (type II/HIGH

(CrO2)), adjust the REC LEVEL control so that the highest

peak is +4 dB. When using Metal position tapes (type IV/

METAL), adjust the REC LEVEL control so that the highest

peak is +6 dB. (Refer to the figure below.)

When a tape is loaded,

the corresponding tape

type indicator lights.

Linear time tape counter

Tape remain indicator

Lights during rec pause mode or

recording. Blinks while the sound

muted section is recorded.

To monitor the sound to be recorded

MONITOR

SOURCE

TAPE

MONITOR

SOURCE

TAPE

Highest peak for Normal or High position tapes

–30 20 15 10 8 6 4 0 2

Highest peak for Metal position tapes

–30 20 15 10 8 6 4 0 2

Linear time tape counter

Use the linear time tape counter as an aid in locating a point

on a tape (–99 min. 59 sec. to 99 min. 59 sec.). To set the

counter reading to “0:00”, press the COUNTER RESET

button.

Note: Precision of counter

The tape counter is not a clock, and so there will be some

errors in the time display compared to the actual recording

time (this cannot be avoided, as a suitable method is

adopted to provide a time display not only during recording

and playback, but also during fast forward and rewind).

The error depends on the type of tape being used.

Tape remain indicator

The tape remain indicator shows the remaining length of the

loaded tape to be recorded.

When the recording reaches the end of the tape, the leftmost

digit of the tape remain indicator blinks.

Lights when a tape is loaded.

Indicates the remaining tape length.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha KX10 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info