Bedienungsanleitung Yamaha mcx 1000 (Seite 139 von 148) (Englisch)

159232

139

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Appendix

139

The MCX-1000 does not record

or playback from the analog input

jacks.

The analog level is set too low. → Use the level adjustment dial on the

front panel of the MCX-1000 to set

an appropriate recording level.

You cannot change from external

input to another playback option.

The MusicCAST is recording from an

external input.

→ Stop recording from an external

source.

Playback changes from the

external input for no apparent

reason.

Another operator is changing sources. → Stop the operator from changing

sources.

The MCX-1000 does not control

the AV receiver correctly.

You are using a straight-type RS-232C

cable.

→ Use a cross-type RS-232C cable.

You have not set the MCX-1000 to

change AV receiver settings.

→ Set The MusicCAST server to

change AV receiver settings.

91, 122

The AV receiver 6 channel input

parameter, is set to “ON”.

→ Set the AV receiver 6 channel setting

to “OFF”.

The correct time is not displayed. The power cord has been disconnected

from an AC outlet for more than 1

minute.

→ The MCX-1000 holds backup data

for no longer than 1 minute after the

power cord is disconnected from the

AC outlet. Disconnecting it for

longer than this will reset the internal

clock. Reconnect the power cord

within one minute of disconnection.

There is a gap between MP3

songs.

MP3 songs are encoded individually. This is not a defect in the MCX-1000.

There is no sound from analog

inputs.

The external component is not

connected correctly.

Correct the component correctly.

The ANALOG REC LEVEL on the

MusicCAST server front panel is too

low.

Increase the ANALOG REC LEVEL.

Playback is delayed or starts at

the wrong place on the CD.

The CD is scratched or dirty. Check the CD, and replace it if

necessary.

The speakers emit a humming

sound.

Connect your components correctly. Connect the stereo pin cables firmly.

The remote control does not

appear to function correctly.

The batteries in the remote control are

exhausted.

Replace both batteries with new ones.

You are attempting to operate the

MCX-1000 from too far away.

You are not aiming the remote

controller at the MCX-1000.

Use the remote control within a 60

degree arc, no further than 6 meters

from the MCX-1000.

Bright light (such as sunlight or light

from a fluorescent lamp) is striking the

remote control sensor.

Relocate the MCX-1000 so that no

bright light strikes the remote control

sensor.

Functioning of your TV is

impaired.

The television is using an indoor

antenna.

Use an outdoor antenna with your

television.

Playback on the MCX-A10 skips

or pauses.

The current state of your network

(wired or wireless) is preventing

smooth playback.

Try stopping playback and/or

recording.

SYMPTOM CAUSE REMEDY PAGE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha mcx 1000 Seite 139

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha mcx 1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info