Bedienungsanleitung Yamaha mg 82 cx live mixer met 8 kanalen (Seite 15 von 21) (Englisch)

425044

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

MG82CX/MG102C Owner’s Manual

Reference

Troubleshooting

* The MG82CX feature is described ﬁrst, followed by the MG102C feature in brackets: MG82CX (MG102C).

■ Power doesn’t come on. ❑ Is the supplied power adaptor properly plugged into an appropriate AC wall outlet?

❑ Is the supplied power adaptor properly plugged into the mixer?

■ No sound. ❑ Are microphones, external devices, and speakers connected correctly?

❑ Are the channel GAIN controls, LEVEL controls, STEREO Master control set to

appropriate levels?

❑ Is the MONITOR switch set properly?

❑ Are your speaker cables connected properly, or are they shorted?

❑ If the above checks do not identify the problem, call Yamaha for service. (Refer to

the page 59 for a list of service centers.)

■ Sound is faint,

distorted, or noisy.

❑ Are the channel GAIN controls, LEVEL controls, STEREO Master control set to

appropriate levels?

❑ Are two different instruments connected to the XLR-type and phone jacks, or to the

phone and RCA pin jacks on one channel? Please connect to only one of these

jacks on each channel.

❑ Is the input signal from the connected device set to an appropriate level?

❑ Are you applying the effects at an appropriate level?

❑ Are microphones connected to the MIC input jacks on channels 1 to 5/6?

❑

If you are using condenser microphones, is the PHANTOM +48 V switch turned ON?

■ No effect is applied.

(If you are using

MG82CX)

❑ Check that the EFFECT control on each channel is correctly adjusted.

❑ Be sure that the internal effect unit’s ON switch is turned ON.

❑ Be sure that the EFFECT PARAMETER control and EFFECT RTN control are cor-

rectly adjusted.

■ I want spoken words to

be heard more clearly.

❑ Be sure that the switches are ON.

❑ Adjust the equalizers (HIGH, MID and LOW) on each channel.

■

I want to output a monitor

signal through speakers.

❑ Connect a powered speaker to the EFFECT (AUX) jack*. Then adjust the output

signal by using the EFFECT (AUX) controls* on each channel.

Mounting to a Microphone Stand

Turn the mixer upside-down, and hold the

microphone-stand adaptor (BMS-10A; sold

separately) against the bottom of the mixer

so that the screw holes are aligned (

1).

Screw the adaptor ﬁrmly into place with the

two screws (

2).

Turn the mixer right-side up, and mount it

onto your microphone stand.

Loosen the angle adjustment wingnut (1),

adjust the mixer’s angle as desired (

2), and

then tighten the wingnut securely (

3).

For more information, refer to the BMS-10A Owner’s

Manual.

•

When using the mixer on a microphone stand, be

sure to set the stand on a level and stable sur-

face. Do not set up the stand in locations subject

to vibrations or wind.

•

Note that mixer may be damaged if the stand

should fall over. Attach the connection cables care-

fully so that the cables will not catch on the equip-

ment and cause it to fall. For example: arrange the

cables so that they run parallel with the micro-

phone pole down to the base of the stand.

•

Leave ample free space around the stand.

CAUTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha mg 82 cx live mixer met 8 kanalen Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha mg 82 cx live mixer met 8 kanalen

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info