Bedienungsanleitung Yamaha MG16XU (Seite 17 von 40) (Englisch)

655877

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

MG20XU/MG20/MG16XU/MG16/MG12XU/MG12 Owner’s Manual

Controls and Connectors

r [PAD] switch

When this switch is turned on ( ), the input signal from

the [MIC/LINE] jack of the mono input channel is attenuated

by 26 dB. Turn this switch off ( ) if you’ve connected a

microphone or other device with a low input level to the

channel. Turn it on ( ) if you’ve connected a line-level

device.

NOTE

There may be some noise when operating switches. To prevent

this, turn the [ON] switch of a channel off before operating

other switches.

t [HPF] (High Pass Filter) switch

Turning this switch on ( ) will apply a high-pass filter that

attenuates frequencies below 80 Hz in the signal by a slope of

12 dB/octave.

NOTE

Turning the [HPF 80Hz (MIC)] switch on will apply a dedicated

high-pass filter only to the signal from the [MIC] jacks.

y [GAIN] knobs

For adjusting the gain of the input signal. Mono input chan-

nels have a [PAD] switch r that lets you change the range of

this control.

The adjustable gain range is as follows.

u [COMP] knobs

For adjusting the amount of compression applied to the chan-

nel. As the [COMP] knob is turned to the right the threshold,

ratio, and output gain are adjusted simultaneously.

• Threshold: +22 dBu to -8 dBu

• Ratio: 1:1 to 4 :1

• Output gain: 0 dB to +7 dB

• Attack time: Approximately 25 ms

• Release time: Approximately 300 ms

NOTE

Avoid setting the compression too high; since the resulting

higher average output level may lead to feedback.

i [PHANTOM +48V] switch and indicator

This switch toggles phantom power on and off. Turn this

switch on ( ) to supply DC+48 V to the XLR input jacks.

The indicator lights when this switch is on. Turn this switch

on when using one or more phantom-powered condenser

microphones.

NOTICE

• Be sure to leave this switch off ( ) if you do not need

phantom power.

• When turning phantom power on ( ), pay careful

attention to the following to prevent damage or noise in

the mixing console or connected equipment.

- Turn this switch off if equipment that does not use

phantom power is connected to the XLR input jacks.

- Do not disconnect XLR connector cables while this

switch is on.

- Set output controls such as the [STEREO] master

fader and the [GROUP] fader to their minimum levels

before turning phantom power on or off.

o [LINE /USB ] switch (XU models)

Switches the audio source input on CH19/20 USB IN {CH15/

16 USB IN} {CH11/12USB IN} between the [LINE] stereo

input jack and the [USB 2.0] jack.

NOTE

The volume input from computers through [USB 2.0] jack can

be adjusted by Attenuator Function. Please see Attenuator

Function (page 28).

[PAD] switch Range

ON -6 dB to +38 dB

OFF +20 dB to +64 dB

MG20XU/MG20: 1 – 12 13/14 – 19/20

MG16XU/MG16: 1 – 8 9/10 – 11/12

MG12XU/MG12: 1 – 4 5/6 – 7/8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MG16XU Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MG16XU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info