Bedienungsanleitung Yamaha MG20 (Seite 18 von 40) (Englisch)

655876

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Controls and Connectors

MG20XU/MG20/MG16XU/MG16/MG12XU/MG12 Owner’s Manual

!0 Equalizer ([HIGH]/[MID]/[LOW])

Equalization Types and Characteristics

The equalizer shapes the high, mid, and low audio frequen-

cies. Turning the knob to the right amplifies (boosts) the cor-

responding frequency band, while turning it to the left

attenuates (cuts) the band. Setting the knob to the middle “t”

position produces a flat response in the corresponding band.

The upper knob sets the variable mid frequency, while the

lower knob sets the amount of attenuation or boost (counter-

clockwise/clockwise) for the range.

The following table shows the EQ type, frequency, and cut/

boost range for each of the three bands.

* The signals from mono input jacks of the MG20XU/MG20

and MG16XU/MG16 can be adjusted from 250 Hz to 5 kHz.

!1 [AUX 1 – 4] knobs

[PRE] switches

[AUX (2, 4)/FX] knobs

The levels of each signal sent to the AUX 1 –

4 buses from each channel can be adjusted

independently. On stereo input channels, the

Line L (odd) and Line R (even) input signals

are mixed before being sent to each AUX

bus. Adjust the knobs so that they are near or

at the “t” (nominal) position.

NOTE

• The [AUX1] knob indicated “PRE” adjusts the level of the pre-

fader signal (before fader adjustment).

• The [PRE] switch on [AUX1] and [AUX2] can be used to

select whether the pre-fader ( ) (the signal before fader

adjustment) or post fader ( ) (the signal after fader adjust-

ment) signal is sent to the AUX bus by the [PRE] switch.

• The [AUX4/FX] and [AUX2/FX] knobs are used to adjust the

level of the signal sent to the FX bus (built-in effects) in addi-

tion to the AUX bus. The same signal level is sent to the AUX

buses and FX buses connected to these knobs.

!2 [PAN] knobs

[PAN/BAL] knobs

[BAL] knobs

• PAN: Sets the position of the sound image within the

stereo field. This knob adjusts the volume bal-

ance of each channel sent to the STEREO L/R

bus. When the knob is set to the 12 o’clock posi-

tion, the channel’s sound will be sent to the L and

R of the STEREO L/R bus at the same volume. In

this case, the sound image is positioned at the

center. If the bus assign switch [1-2] or [3-4] is

pressed, this knob adjusts the volume balance

sent to the GROUP bus. When the knob is set to

the 12 o’clock position, the same volume is sent

to each GROUP bus. If the knob is turned com-

pletely to the left, the signal is sent to the GROUP

1 or GROUP 3 bus only; if the knob is turned

completely to the right, the signal is sent to the

GROUP 2 or GROUP 4 bus only.

3 Band

[MID] Sweep

3 Band 2 Band

MG20XU/

MG20

CH 1 – 12

CH 13/14 –

19/20

—

MG16XU/

MG16

CH 1 – 8

CH 9/10 –

15/16

—

MG12XU/

MG12

— CH 1 – 7/8

CH 9/10 –

11/12

Band Type Frequency

Cut/Boost

range

HIGH Shelving 10 kHz

±15 dBMID Peaking 2.5 kHz*

LOW Shelving 100 Hz

3 Band

[MID] Sweep

3 Band 2 Band

MG20XU/MG16XU: [AUX1],

[AUX2 – 3], [AUX4/FX]

MG20/MG16: [AUX1], [AUX2 – 4]

MG12XU: [AUX1], [AUX2/FX]

MG12: [AUX1 – 2]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MG20 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MG20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info