Bedienungsanleitung Yamaha Montage 6 (Seite 68 von 86) (Englisch)

652603

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

MONTAGE Owner’s Manual

No sound? Wrong sound? When a problem like this occurs, please check the following points before assuming that the product

is faulty. Many problems can be solved by executing Data Initialization (page 15), after backing up your data to an USB flash

memory device (page 53). If the problem persists, consult your Yamaha dealer.

Touch panel does not respond correctly.

 Is the point you touch on the touch panel lined up properly with the target item in the display underneath?

Calibrate the touch panel.

No Sound.

 Are all sliders set to appropriate levels (other than zero or minimum)?

 Is the MONTAGE properly connected to related external equipment (e.g., amplifier, speaker, headphones) via audio cables?

Since the MONTAGE has no built-in speakers, you will need an external audio system or a set of stereo headphones to

properly monitor it (page 14).

 Is the power of this synthesizer and any external equipment connected to this synthesizer turned on?

 Have you made all the appropriate level settings—including the Master Volume on this synthesizer and the volume settings on

any connected external equipment?

When the Foot Controller is connected to the [FOOT CONTROLLER] jack, press the Foot Controller down.

 Is the Local Control parameter set to off?

When the Local Control parameter is set to off, no sound is produced even if you play the keyboard.

 Is a blank Part selected?

If so, assign any sound to the Part or select another Part.

 Is the Mute switch for each Part turned on?

When the Mute switch is turned on, no sound is produced even if you play the keyboard.

 Is the Keyboard Control of each Part turned off?

 Is the “Arp Play Only” parameter of each Part turned on?

When this parameter is turned on, the corresponding Part produces sound only via Arpeggio playback.

 Are the MIDI volume or MIDI expression settings too low when using the external controller?

 Are the effect and filter settings appropriate?

If you are using a filter, try changing the cutoff frequency. Some cutoff settings may filter out all of the sound.

• In case of Normal Part (AWM2) and Drum Part

• In case of Normal Part (FM-X)

 Is “Vocoder” selected as the Insertion Effect Type of the Part?

If so, set the parameters related to the A/D INPUT [L/MONO]/[R] jack to the appropriate values then play the keyboard while

inputting your voice into the microphone connected to the MONTAGE. Check whether or not the A/D INPUT [GAIN] Knob on

the rear panel is set to the minimum position.

Troubleshooting

[UTILITY] + PART [COMMON]  [ENTER]

[UTILITY]  [Settings]  [System]  [Calibrate Touch Panel]

[UTILITY]  [Settings]  [MIDI I/O]  “Local Control”

[PERFORMANCE]  Part selection  “Mute”

[PERFORMANCE]  Part selection  “Kbd Ctrl”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Part Settings]  [General]  “A r p P l ay O n l y ”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Arpeggio]  [Common]  “Arp Play Only”

[EDIT]  PART [COMMON]  [Effect]

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Effect]

[EDIT]  Part selection  Element/Key selection  [Filter]

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Pitch/Filter]

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Effect]  [Routing]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha Montage 6 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info