Bedienungsanleitung Yamaha Montage (Seite 70 von 86) (Englisch)

707383

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

MONTAGE Owner’s Manual

Troubleshooting

Playback continues without stopping.

 When the [ARP ON/OFF] button is turned on, press it so that the button is turned off.

 When in the Song display, press the [J] (Stop) button.

 When the effect sound such as Delay continues, check the effect setting or select the Performance again.

 When the click sound continues, check the following parameter setting. Set this parameter to something other than “always,”

since this setting always plays back the click sound regardless of the sequencer status.

Distorted sound.

 Are the effect settings appropriate?

Use of an effect at certain settings may produce distortion.

 Are the filter settings appropriate?

Excessively high filter resonance settings can cause distortion.

• In case of Normal Part (AWM2) and Drum Part

• In case of Normal Part (FM-X)

 Are any of the following volume parameters set so high that clipping is occurring?

• In case of Normal Part (AWM2) and Drum Part

• In case of Normal Part (FM-X)

Sound is cut off.

 Is the entire sound (via your keyboard playback and Song/Part/Arpeggio playback) exceeding the maximum polyphony (128

for each of AWM2 and FM-X) of the MONTAGE?

Only one note sounds at a time.

 When this situation occurs, the Mono/Poly parameter in the current mode is set to “mono.”

If you wish to play chords, set this parameter to “poly.”

Pitch or intervals are wrong.

 Is the Master Tune parameter of each Part set to a value other than “0”?

 Is the Note Shift parameter of each Part set to a value other than “0”?

• In case of Normal Part (AWM2) and Drum Part

• In case of Normal Part (FM-X)

[UTILITY]  [Tempo Settings]  Click “Mode”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Effect]

[EDIT]  Part selection  Element/Key selection  [Filter]

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Pitch/Filter]

[UTILITY]  [Settings]  [Sound]  Tone Generator “Volume”

[UTILITY]  [Settings]  [Audio I/O]  “Output”

[EDIT]  PART [COMMON]  [General]  “Volume”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Part Settings]  [General]  “Volume”

[EDIT]  Part selection  Element/Key selection  [Amplitude]  [Level/Pan]  “Level”

[EDIT]  Part selection  Operator selection  [Level]  “Level”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Part Settings]  [General]  “Mono/Poly”

[UTILITY]  [Settings]  [Sound]  Tone Generator “Tune”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Part Settings]  [Pitch]  “Note Shift”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Part Settings]  [Pitch]  “Detune”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Pitch/Filter]  [Pitch]  “Note Shift”

[EDIT]  Part selection  ELEMENT/OPERATOR [COMMON]  [Pitch/Filter]  [Pitch]  “Detune”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha Montage Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha Montage

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info