Bedienungsanleitung Yamaha MOTIF ES7 (Seite 155 von 300) (Englisch)

571272

155

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

Basic Structure

Internal Structure (System Overview)

155

Owner’s Manual

Controller related parameters in each mode

The chart below shows the operations for calling up the Controller related parameters in each mode. Parameters for the

Footswitch and the Assign Knobs A/B apply to the entire instrument, regardless of the selected program (Voice/Performance/

Song/Pattern).

Aside from their default control parameters, the controllers of the instrument, such as the Pitch Bend wheel and the Modulation

wheel, can be freely assigned to a variety of different parameters. For example, you could assign Resonance to the Modulation

Wheel and set aftertouch to apply vibrato. These settings for all the controllers are referred to as a “Controller Set,” and up to six

Controller Sets can be created for each Voice.

● Source and Destination

“source” refers to the hardware controller and “destination” refers to the parameter or function being controlled. An extensive

variety of destination parameters are available, far more than those listed above. For a complete list of destination parameters,

see the separate Data List.

Voice mode

Controller Set (for each Voice) [VOICE] → Voice selection → [EDIT] → [COMMON] → [F4] CTL SET See below.

Assigning the Control Change number to each

Controller (for all Voices) [VOICE] → [UTILITY] → [F3] VOICE → [SF4] CTL ASN Page 262

Performance

mode Assigning the Control Change number to each

Controller (for each Performance)

[PERFORM] → Performance selection → [EDIT] → [COMMON] →

[F4] CTL ASN Page 214

Song mode Assigning the Control Change number to each

Controller (for each Song Mixing)

[SONG] → Song selection → [MIXING] → [EDIT] → [COMMON] →

[F4] CTL ASN Page 234

Pattern mode Assigning the Control Change number to each

Controller (for each Pattern Mixing)

[PATTERN] → Pattern selection → [MIXING] → [EDIT] → [COMMON] →

[F4] CTL ASN Page 248

All modes

Assigning the function and Control Change

number to the Assign Knob A/B [UTILITY] → [F4] CTL ASN → [SF2] ASSIGN Page 263

Assigning the function and Control Change

number to the Footswitch (connected to the

ASSIGNABLE connector)

[UTILITY] → [F4] CTL ASN → [SF3] FT SW Page 263

Controller Set [VOICE] →→

→→ Voice selection →→

→→ [EDIT] →→

→→ [COMMON] →→

→→ [F4] CTL SET Page 192

SWING GATE TIME

LOW

KN 1

LOW MID

KN 2

ON/OFF ON/OFF ON/OFF ON/OFF

234

Voice

Controller Set 1 - 6

Volume, Reverb Send Level, Chorus Send Level, Filter

Cutoff Frequency, Filter Resonance, etc.

Controller Set

Source = Controller

Depth = Degree to which the

controller affects the sound

Element Switches

Destination (Dest) = function

nYou can set whether the controller affects each

Element by setting the Element Switch on or off as

desired. Note that this applies only to Normal Voices.

nThe Element Switch parameters are not available

when a function unrelated to Elements (1 - 40) is set

as the destination.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF ES7 Seite 155

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF ES7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info