Bedienungsanleitung Yamaha MOTIF-RACK XS (Seite 81 von 118) (Englisch)

586891

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

Voice Mode

MOTIF-RACK XS Owner’s Manual

Basic Structure

Voice

MultiUtility

Reference

The Controls &

Connectors

Setting Up

Listening to

the Sound

Connections

Using a Computer

Quick Guide

Appendix

Time Key Follow

(EG Time Key Follow Sensitivity)

Determines the degree to which the notes (speciﬁcally, their position or octave range) affect the

Amplitude EG times of the selected Element. When this is set to a positive value, high notes result in

a fast Amplitude EG transition speed while low notes result in a slow speed. When this is set to a

negative value, the opposite effect is produced: High notes result in a slow Amplitude EG transition

speed while low notes result in a fast speed. When this is set to 0, the Amplitude EG transition speed

does not change no matter what the pressed note.

Settings: -64 – +0 – +64

AMP Scale (Amplitude Scale)

Break Point 1 – 4 Determines the four Break Points by specifying the respective note numbers.

Settings: C -2 – G8

n Break Point 1 to Break Point 4 will be automatically be arranged in ascending order across the keyboard.

Level Offset 1 – 4 Determines the offset value to the level at each Break Point. For details about Amplitude Scaling,

refer to “Setting example of Amplitude Scaling” (page 90) in the Supplementary information.

Settings: -128 – +0 – +127

LFO (Low Frequency Oscillator)

LFO Wave Selects the Wave and determines how the LFO waveform modulates the sound.

Settings: saw, triangle, square

Speed Determines the speed of the LFO Wave.

Settings: 0 – 63

Key on Reset When this is set to on, the LFO waveform is reset every time a Note On message is received.

Settings: off, on

off ...................................... The LFO cycles freely with no key synchronization. Receiving a Note On message starts the

LFO wave at whatever phase the LFO happens to be at that point.

on ...................................... The LFO resets with each received note and starts a waveform at the phase speciﬁed by the

Phase parameter (page 69).

Delay Determines the delay time between the moment a Note On message is received to the moment the

LFO comes into effect. A higher value results in a longer delay time.

Settings: 0 – 127

Fade in Time Determines the amount of time for the LFO effect to fade in after the Delay time has elapsed. A

higher value results in a slower fade-in. When set to “0,” the LFO effect will not fade in and reach the

maximum level immediately after the Delay time has elapsed.

Settings: 0 – 127

P Mod

(Pitch Modulation)

Determines the amount (depth) by which the LFO wave varies (modulates) the pitch of the sound.

The higher the setting, the greater the depth of control.

Settings: 0 – 127

F Mod

(Filter Modulation)

Determines the amount (depth) by which the LFO wave varies (modulates) the Filter Cutoff

frequency. The higher the setting, the greater the depth of control.

Settings: 0 – 127

A Mod

(Amplitude Modulation)

Determines the amount (depth) by which the LFO wave varies (modulates) the amplitude or volume

of the sound. The larger the setting, the greater the depth of control.

Settings: 0 – 127

Type

(EQ Type)

Determines the EQ Type. The number of parameters and values available differs depending on the

selected EQ type.

Settings: 2 Band (2 Band EQ), P.EQ (Parametric EQ), Boost 6 (Boost +6dB), Boost 12 (Boost +12dB), Boost18 (Boost

+18dB), thru

2 Band............................... This is a “shelving” equalizer, which combines separate high and low frequency bands.

P.EQ................................... The Parametric EQ for the single band is used to attenuate or boost signal levels (gain) around

the Low Freq according to the settings of Low Gain. Determines the bandwidth with which the

sound will be boosted or cut in the “Q” parameter.

Boost 6, Boost 12, Boost18

.......................................... Boosts the entire band of the selected Element by +6dB, +12dB, and +18dB respectively.

These settings have no adjustable parameters.

thru .................................... If you select this, the equalizers are bypassed and the entire signal is unaffected.

Low Freq This parameter is available only when the Type (EQ Type) parameter is set to “2 Band” or “P.EQ.”

When setting to “2 Band,” this determines the center frequency of the lower EQ band. When setting

to “P.EQ,” this determines the center frequency.

Settings: When the Type is set to “2 Band”... 50.1Hz – 2.00kHz, When the Type is set to “P.EQ”... 139.7Hz – 12.9kHz

High Freq This parameter is available only when the Type (EQ Type) parameter is set to “2 Band.” This

determines the center frequency of the high EQ band.

Settings: 503.8Hz – 10.1kHz

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF-RACK XS Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF-RACK XS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info