Bedienungsanleitung Yamaha MOTIF XF8 (Seite 39 von 86) (Englisch)

571282

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

MOTIF XF Owner’s Manual

Creating an original Song

2 Press the [ARPEGGIO ON/OFF] button so that the

lamp lights.

3 Press the [] (Record) button to enter the Song

Record mode.

4 Press the [F1] button to call up the Record Setup

display.

5 Set the following parameters in the Record Setup

display.

5-1 To select the desired track, press the [TRACK] button (the

lamp lights), then press the appropriate Number button

[1] – [16].

5-2 Set the Time Signature to “4/4.”

5-3 Set the Quantize parameter to “off.”

6 Press the [F2] button to call up the Record

Arpeggio display.

7 Set the following parameters as required in the

Arpeggio Record display.

7-1 Set the Switch parameter to on.

7-2 Set the Voice with Arpeggio (ARP) parameter to on.

When this is set to “on,” the Voice matching the selected

Arpeggio type is automatically called up each time the

Arpeggio type is changed.

7-3 Select the Arpeggio type by specifying the Category, Sub

Category and Type.

8 After completing recording setup, press the [R]

(Play) button to start recording.

Press the [R] (Play) button so that its indicator flashes, then

actually start recording after the count-in.

9 When you reach the end of the above notation,

press the [] (Stop) button to stop recording.

If you’ve played any wrong notes, press the [] (Stop)

button, then try recording again.

Correcting wrong notes

If you’ve played any wrong notes while recording and wish to

correct them, press the [EDIT] button from the Song Play

mode to go to the Song Edit mode. Song Edit lets you clean

up and edit data of already recorded Songs or insert new

data to the Songs.

Check for any mistakenly recorded or wrong events on the

Event List display of the Song Edit mode, then correct them

as needed.

1 Select the recorded Song then press the [EDIT]

button to enter the Song Edit mode.

The Event List display appears.

2 Select the track to be edited.

Press the Number button [1]. The list of the MIDI events

recorded in the previous section appears on the display.

NOTE

Various MIDI events as well as note on/off data are shown on

the display if you operate controllers such as Pitch Bend

wheel, knobs and sliders while recording.

3 Use the Cursor buttons to move the cursor to the

location to be edited.

After confirming the location at which the wrong data is

recorded, use the Up/Down Cursor button to move the

cursor to the location, then use the Left/Right Cursor button

to move the cursor to the data type to be corrected. For

example, if you recorded a wrong note data at the 2nd note

of the 3rd beat, move the cursor to the location indicated

MEAS (measure) = 002, BEAT = 03 and CLOCK = 240.

Then, move the cursor to NOTE if you wish to correct the

note data and move the cursor to GATE if you wish to correct

the gate time (note length).

NOTE

Each key has a note name; for example, the lowest (farthest

left) key on the keyboard corresponds to C1 and the highest

(farthest right) key to C6. See page 10.

Recording Track Time Signature

Quantize

Arpeggio

Switch

Voice with

Arpeggio

type

selection

Location Notes

Velocity

Selected track

Gate time

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF XF8 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF XF8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info