Bedienungsanleitung Yamaha MOTIF XS7 (Seite 293 von 320) (Englisch)

586887

293

Zoom out

Zoom in

Vorherige Seite

1/320

Nächste Seite

MOTIF XS Owner’s Manual 293

Appendix

Installing Optional Hardware

Available devices

The following optional devices can be installed to the

MOTIF XS.

Installation locations

mLAN16E2

DIMM

Installation Precautions

Before installing the optional hardware, make sure you

have a Philips screwdriver and ample space to work.

• Before beginning installation, switch off the power to the

instrument and connected peripherals, and unplug them from

the power outlet. Installation or removal of any devices should

be started ONLY after the instrument (and the optional

hardware) returns to normal room temperature. Then remove all

cables connecting the instrument to other devices. (Leaving the

power cord connected while working can result in electric

shock. Leaving other cables connected can interfere with work.)

• Be careful not to drop any screws inside the instrument during

installation. (This can be prevented by keeping the optional

units and cover away from the instrument while attaching). If this

does happen, be sure to remove the screw(s) from inside the

unit before turning the power on. Loose screws inside the

instrument can cause improper operation or serious damage. If

you are unable to retrieve a dropped screw, consult your

Yamaha dealer for advice.

•Install the optional units carefully as described in the procedure

below. Improper installation can cause shorts which may result

in irreparable damage and pose a ﬁre hazard.

• Do not disassemble, modify, or apply excessive force to board

areas and connectors on optional units. Bending or tampering

with boards and connectors may lead to electric shock, ﬁre, or

equipment failures.

• It is recommended that you wear gloves to protect your hands

from metallic projections on optional units and other

components. Touching leads or connectors with bare hands

may cause ﬁnger cuts, and may also result in poor electrical

contact or electrostatic damage.

• Be careful of static electricity. Static electricity discharge can

damage the IC chips on the mLAN16E2. Before you handle the

optional mLAN16E2, to reduce the possibility of static electricity,

touch unpainted metal parts or a ground wire on the devices

that are grounded.

•Handle the optical units with care. Dropping or subjecting them

to any kind of shock may cause damage or result in a

malfunction.

• Do not touch the exposed metal parts in the circuit board.

Touching these parts may result in a faulty contact.

• Be careful not to misplace any of the screws.

• Do not use any screws other than what are installed on the

instrument. Use of incorrect screws can cause damage.

mLAN16E2 DIMMs

POWER

ON/ OFF

AC IN

THRU

MIDI

OUT IN PHONESPHONES

ASSIGNABLE SUSTAIN

FOOT SWITCH FOOT CONTROLLER

ASSIGNABLE OUTPUT OUTPUT

RRL L/MONO

DIGITAL OUT

A/D INPUT

RLGAIN

LCD CONTRASTETHERNET

USB

TO DEVICETO HOST

MOTIF XS6

MOTIF XS7

Rear cover for the mLAN16E2

MOTIF XS6

MOTIF XS7

MOTIF XS8

Bottom cover for the DIMM

WARNING

CAUTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF XS7 Seite 293

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF XS7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info