Bedienungsanleitung Yamaha MOTIF XS8 (Seite 288 von 320) (Englisch)

586888

288

Zoom out

Zoom in

Vorherige Seite

1/320

Nächste Seite

MOTIF XS Owner’s Manual

288

Appendix

Troubleshooting

No sound? Wrong sound? When a problem like this occurs, please check the following points before assuming that the

product is faulty. You may solve your problem by executing the Factory Set (page 22) after backing up your data to an

external storage device. If the problem persists, consult your Yamaha dealer.

No Sound.

■Are all eight sliders set to appropriate levels (other than zero or minimum)?

■Is the MOTIF XS properly connected to related external equipment (e.g., ampliﬁer, speaker, headphone) via audio cables?

Since the MOTIF XS has no built-in speakers, you will need an external audio system or a set of stereo headphones to properly

monitor it.

■Check the Local Control parameter and the mLAN Monitor Setup parameter in the Utility mode.

When the MOTIF XS is used as stand alone and the Local Control parameter is set to off or the mLAN Monitor Setup parameter is

set to “with PC,” no sound is produced even if you play the keyboard.

■Is the power of this synthesizer and any external equipment connected to this synthesizer turned on?

■Have you made all the appropriate level settings—including the Master Volume on this synthesizer and the volume settings on

any connected external equipment?

■Is the Foot Controller pressed down (when it is connected to the FOOT CONTROLLER jack)?

■Are the MIDI volume or MIDI expression settings too low when using the external controller?

■Is this synthesizer properly connected to related external equipment (e.g., ampliﬁer or speaker) via audio cables?

■Are the effect and ﬁlter settings appropriate?

If you are using the ﬁlter, try changing the cutoff frequency. Some cutoff settings may ﬁlter out all of the sound.

■Are the volume or expression settings too low?

■Are the parameter settings such as Element Switch, Part Switch, Note Limit and Velocity Limit appropriate?

■When the Element to which “Legato” of the XA Control parameter is assigned does not sound, is the Mono/Poly parameter of the

Element set to “Mono”? Or, is a value other than “Legato” of the XA Control parameter assigned to another Element within an

Element Group?

■When the Element to which “Key Off Sound” of the XA Control parameter is assigned does not sound, are you releasing the note

after the AEG decays?

The “Key Off Sound” Element will take over the AEG level of the previous Element if both the Elements belong to the same

Element Group. To solve such a problem, release the note before the AEG level decays to minimum or set the “Key Off Sound”

Element to the different Element Group from the previous Elements.

[UTILITY] → [F5] Control → [SF2] MIDI → Switch → Local Control (page 269)

[UTILITY] → [F2] I/O → mLAN Monitor Setup (page 263)

[VOICE] → [EDIT] → [COMMON EDIT] → [F6] Effect (page 107)

[PERFORM] → [EDIT] → [COMMON EDIT] → [F5] Effect (page 149)

[SONG]/[PATTERN] → [MIXING] → [F5] Effect (page 234)

[VOICE] → [EDIT] → Element/Key selection → [F3] Filter (page 117)

[PERFORM] → [EDIT] → Part selection → [F4] EG → Filter (page 158)

[SONG]/[PATTERN] → [MIXING] → [EDIT] → Part selection → [F4] EG → Filter (page 235)

[PERFORM]/[SONG]/[PATTERN] → [SEQ SETUP] → [F2] MIDI Filter (page 270)

[UTILITY] → [F1] General → [SF1] Play → Volume (page 259)

[VOICE] → [EDIT] → [COMMON EDIT] → [F1] General → [SF2] Play Mode → Volume (page 98)

[VOICE] → [EDIT] → Element/Key selection → [F4] Amplitude → [SF1] Level/Pan → Level (page 122)

[PERFORM] → [EDIT] → [COMMON EDIT] → [F2] Level/MEF → [SF1] Level → Volume (page 145)

[PERFORM] → [EDIT] → Part selection → [F1] Voice → [SF1] Voice → Volume (page 152)

[SONG]/[PATTERN] → [MIXING] → [F1] Part 1-16 → Volume (page 232)

[VOICE] → [EDIT] → Element/Key selection → [F1] Oscillator (page 112)

[PERFORM] → [F2] Voice (page 138)

[PERFORM] → [EDIT] → Part selection → [F1] Voice → [SF1] Voice → Part Switch (page 151)

[VOICE] → [F2] Porta → Mono/Poly Mode = mono (page 93)

[VOICE] → [EDIT] → Element selection → [F1] Oscillator → XA Control (page 112)

[VOICE] → [EDIT] → Element selection → [F1] Oscillator → Element Group (page 113)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF XS8 Seite 288

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF XS8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info