Bedienungsanleitung Yamaha MOTIF8 (Seite 200 von 300) (Englisch)

571289

200

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

200

MOTIF Reference

Song Job mode

Reference Song mode

• Number Of Times

Determines the number of times the data creation is to be

repeated.

For example, if data is created in the range M001:1:000 ~

M003:1:000 and this parameter is set to 03, the same data

will be created at M003:1:000 ~ M005:1:000 and

M005:1:000 ~ M007:1:000.

This Job lets you to insert continuous volume or ﬁlter

cutoff variations to create tremolo or wow effects.

❏ Settings 01~99

● [F3]-06 Thin Out

This Job thins out the speciﬁed type of continuous

data in the speciﬁed range — allowing you to free

up memory space for other data or further

recording.

• Event Type

Determines the event type to be thinned.

❏ Settings PB (Pitch Bend), CC: 000-127, all (Control

Change, Control Change number), CAT

(Channel Aftertouch), PAT (Polyphonic

Aftertouch)

n The Thin Out Job will not work on continuous

data that has a clock interval of greater than 60

clocks per event.

● [F3]-07 Modify Control Data

This Job lets you change the values of a speciﬁed

type of control change data — pitch bend, control

change, aftertouch, etc. — in the speciﬁed range.

Data changes are calculated as follows:

Modiﬁed value

= (original value x Rate) + Offset.

The modiﬁed value cannot exceed the minimum/

maximum limits of the parameter. Any result lower

than the minimum is set to the minimum; any result

higher than the maximum is set to the maximum.

• Event Type

Determines the event type to be modiﬁed.

❏ Settings PB (Pitch Bend), CC: 000-127, all (Control

Change, Control Change number), CAT

(Channel Aftertouch), PAT (Polyphonic

Aftertouch), tmp (Tempo)

• Set All

Sets all target events to the same ﬁxed value. When set to

“OFF” the Set All parameter has no effect. When set to a

value other than “OFF” the Rate and Offset parameters

are unavailable and appear as “***” on the display.

❏ Settings OFF, 000 ~127 (-8192 ~ +8191 for pitch

bend, 0.1 ~ 300.0 for tempo)

• Rate

Determines the percentage by which the target events will

be shifted from their original values.

When the Set All parameter is not “OFF” this parameter

appears as “***” and cannot be changed.

❏ Settings 000% ~ 200%, ***

• Offset

Adds a ﬁxed value to the Rate-adjusted event values.

When the Set All parameter is not “OFF” this parameter

appears as “***” and cannot be changed.

❏ Settings -127~127, *** (-8192 ~ +8191 for pitch

bend, ***)

● [F3]-08 Beat Stretch

This Job performs time-expansion or compression

over the selected range.

Keep in mind that this operation affects all event

timing, note step times, and note gate times.

• Rate

Determines the amount of time expansion or compression

as a percentage.

Settings higher than 100% produce expansion, and

settings below 100% produce compression.

❏ Settings 025%~400%

n Only MIDI data is affected by this job. Sample

voices are not expanded or compressed. However,

for samples recorded using the Slice+Seq feature,

the Beat Stretch job expands or compresses the

timing of the note data, step times, and gate times

that control playback of the sliced samples. The

sample voice itself is not affected.

Track

Range

Track

Range

Track

Range

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF8 Seite 200

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info