Bedienungsanleitung Yamaha MOTIF8 (Seite 290 von 300) (Englisch)

571289

290

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

290

MOTIF Appendix

Connecting external SCSI devices

Appendix

Connecting external SCSI devices

This section explains how to connect external devices such as external hard disk drives, MO drives, or CD-ROM drives.

About SCSI

SCSI (pronounced “scuzzy”) stands for Small Computer System Interface, and is a data transmission interface

standard used by personal computers and other devices.

Since the MOTIF has a SCSI interface, you can connect and use hard disk drives, MO disk drives, CD-ROM drives,

and other SCSI-compatible devices that have a 50-pin SCSI connector. Up to 7 SCSI devices can be connected.

Most external SCSI devices have two SCSI terminals, allowing a number of devices to be “chained” together. Devices

chained together in this way can normally be connected in any order.

The last device in the chain must be “terminated,” either with a terminator unit plugged into the open SCSI

connector, or by turning the device's internal terminator on (if available). The ﬁrst device in the chain must also be

terminated, but in the case of the MOTIF this is accomplished by the terminator inside the MOTIF.

• Before connecting SCSI devices, be sure to turn off the power of the MOTIF and all connected equipment. If the power is on

while connections are being made, the MOTIF or SCSI devices can be damaged.

• Including the MOTIF, each SCSI device is distinguished by a number from 0 - 7, called the SCSI ID. If two or more devices have

the same SCSI ID number, the SCSI devices will not function correctly. When shipped from the factory, the MOTIF is set to SCSI

ID 6. Be aware that the SCSI ID number of a device has no relation to its position in the daisy-chain.

• Don't forget to attach a terminator to the last SCSI device in the daisy-chain.

• If an external SCSI device is not connected, it is not necessary to attach a terminator to the external SCSI connector of the

MOTIF.

• Use as short a SCSI cable as possible. Using long cables can cause unreliable operation. In general, the total cable length should be

less than 6 meters (approximately 18 feet).

• Use high-quality SCSI cables. Poor-quality cables can cause unreliable operation.

• Some SCSI devices have only one SCSI connector. If you are using such a device, connect it at the end of the daisy-chain.

Procedure

1 Use SCSI cables to daisy-chain the external SCSI devices.

Since there are several different types of SCSI connectors, make sure to select the proper SCSI cables for your

particular devices.

2 Connect the power cable of the external SCSI device to an AC outlet.

3 Set the SCSI ID (0 - 7) of the external SCSI device.

Select a SCSI ID that will not conﬂict with the other SCSI devices (including the MOTIF). When the MOTIF is

shipped from the factory, the SCSI ID is set to 6.

External SCSI

device

MOTIF

External SCSI

device

External SCSI

device

PLG 2

CATEGORY

OCTAVE

DOWN

KNOB

CONTROL

FUNCTION

PAN

REVERB

CHORUS

TEMPO

ATTACK RELEASECUTOFF

RESONANCE

ASSIGN A ASSIGN B ASSIGN 1 ASSIGN 2

KN 1 KN 2 KN 3 KN 4

MEQ LOW

MEQ HI MIDMEQLOWMID MEQ HIGH

REMOTE

CONTROL

ON/OFF

EFFECT BYPASS

ARPEGGIO

INSERTION

SYSTEM

ON/OFF

MASTER

VOLUME

VOLUME 1 VOLUME 2 VOLUME 3 VOLUME 4

CS 1 CS 2 CS 3 CS 4

ZONE 1 ZONE 2 ZONE 3 ZONE 4

SEQ TRANSPORT

LOCATE

REC

MODE

VOICE PERFORM MASTER

SEQUENCER

SONG

PATTERN

FILE

INTEGRATED

SAMPLING

MIXING

UTILITY

EDIT

JOB

STORE

COMPARE

SCENE STORE

SET LOCATE

SONG SCENE

SF 1SF 2SF 3SF 4SF 5

F1 F2 F3 F4 F6F5

INFORMATION

DEC/NO INC/ YES

EXIT

ENTER

EXECUTE

MUSIC

PRODUCTION

SYNTHESIZER

Integrated

Sampling

Sequencer

Real-timeExternal Control

Surface

Modular

SynthesisPlug-in

System

DRUM KITS

FAVORITES

SLOT 1 SLOT 2 SLOT 3

PRE 1

PRE 2

PRE 3

USER PLG 1

PLG 3

A. PIANO

KEYBOARD

ORGAN

GUITAR/

PLUCKED

BASS

STRINGS

BRASS

REED/PIPE

SYN LEAD SYN PAD/

CHOIR

SYN COMP CHROMATIC

PERCUSSION

DRUM/

PERCUSSION

MUSICAL FX COMBI

SECTION

TRACK

SELECT

MUTE

SOLO

BANK

GROUP

NUMBER

COMMON

ELEMENT/PERF.PART/ ZONE

Indicates the terminator (or a terminator

switch turned ON). For devices not marked

by this symbol, do not attach a terminator

(or turn the terminator off).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF8 Seite 290

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info