Bedienungsanleitung Yamaha MOXF6 (Seite 43 von 80) (Englisch)

571309

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Creating a bass part via Realtime

Recording

Next, record the bass line via Realtime Recording to Track 2.

1 In the Song Play mode, select the same Song

(created above) to which the Drum part has

already been recorded.

2 Press the [REC] button, followed by the [F1]

SETUP button, then set the parameters as below.

• “Type” = “replace”

• “Quantize” = “240”

• “RecTr” = “2”

3 Press the [F2] VOICE button, followed by the

[CATEGORY SEARCH] button then select the Bass

Voice.

Set the “Main” (Main Category) to “Bass” then set the “Sub”

(Sub Category) to “Synth Bass.” Move the Cursor [>] button

to call up the Voice List. From this list, select “PRE3 E01 Uni

Punch” then press the [ENTER] button.

4 Press the [F5] CLICK button to turn the Click

() on.

5 Press [UTILITY]  [F2] SEQ  [SF1] CLICK, then

set the Click related parameters as below.

• “Mode” = “rec”

• “Beat” = “04”

• “RecCount” = “1meas”

With this setting, there will be a one-measure lead-in count

before recording begins and the Click will play back only

while recording.

6 Press the [REC] button to return to the Song

Record display.

7 Press the [P] (Top) button to return to the top of

the Song, then press the [F] (Play) button to start

recording.

As soon as the lead-in count (1-measure) is finished, play

the following notation.

8 After playing the above notation, press the [J]

(Stop) button to stop recording.

If you play any wrong notes, press the [J] (Stop) button,

then try recording again. Repeat as often as necessary until

you get it right.

9 Press the [P] (Top) button followed by the [F]

(Play) button to hear the recorded data.

The recorded data of the Tracks 1 and 2 will be played back.

To stop playback, press the [J] (Stop) button. If you are not

satisfied with the recorded data, try this operation again.

HINT

Re-recording a specific part of a Song

(Punch In/Out)

Use the Punch In/Out recording method to record over only a

specific portion of the Track. If you set the start point (Punch In)

and end point (Punch Out), and then start recording from the

top of the Song, the actual recording will be done only between

the Punch In and Punch Out points. In the eight-measure

example below, only the third through the fifth measures are re-

recorded.

NOTE Punch In/Out Recording can only be used with Realtime

recording.

NOTE

Note that the Punch In/Out method always replaces

(destroys) the original data over the specified area.

To execute Punch In/Punch Out recording in the above condition,

set the following parameters beforehand on the [F1] SETUP

display in the Song Record mode.

• “Type” = “punch”

• Punch In = 003:01

• Punch Out = 006:01

1234567 8

Recording start Recording stop

Before re-recording

Punch In point Punch Out point

After re-recording

Newly recorded data

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOXF6 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOXF6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info