Bedienungsanleitung Yamaha MusicCast - WX-010 (Seite 21 von 28) (Englisch)

706992

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

You can update the firmware only when the unit is connected to the Internet (☞ P.6).

Follow the instructions in the MusicCast CONTROLLER app to update.

While the firmware is being updated, the indicators flashes from the left in order, in accordance with the progress.

Updating completed: All indicators light, and the unit automatically enters standby mode.

Updating failed: All the indicators flash. Unplug the power cable from the wall outlet and plug it in after 30 seconds or

more, then update the firmware again.

• Do not operate the unit or disconnect the power cable or network cables while updating.

• Do not turn off the unit (enter standby) while updating the firmware.

• The update of the firmware will be informed in the app.

• When Internet speed is not fast enough or the unit is connected to the wireless network via a wireless network adapter,

network update may not be possible depending on the condition of the wireless connection.

To set the unit to option setting mode, where you can make the following settings, set the unit to standby, and then touch and

hold and for 5 seconds.

*1: If you do not tap any button during these 10 seconds, the unit will cancel the option setting mode.

*2: Network Standby is a standby which enables the unit to connect to the network by operating another device.

Eco Standby

If you disable Network Standby, the unit enters a standby where indicators and the network/Bluetooth functions are disabled

and where the standby power consumption is kept to a minimum.

While the unit is in Eco Standby, you cannot start it up with the MusicCast CONTROLLER app or specify stereo pair settings.

Perform these operations after turning on the unit by tapping (power)/CONNECT.

UPDATING THE FIRMWARE

OPTION SETTINGS

Items Operations

Initialize the unit.

Touch and hold (power)/CONNECT for 3 seconds (☞ P.3). During initialization, the three

indicators flash for about 20 seconds.

Enable/disable Network

Standby.

Touch and hold for 3 seconds. Network Standby will be disabled. To enable it, perform the same

operation.

Enable: The power indicator flashes twice and remains lit.

Disable: The power indicator flashes twice and turns off.

Disable Wi-Fi.

Touch and hold for 3 seconds. Wi-Fi will be disabled.

The Wi-Fi indicator flashes twice and turns off.

To enable the Wi-Fi function, follow the procedures in “Connecting to the network“ (☞ P.6) and

reconnect the unit to the network.

Enable/Disable Bluetooth.

Touch and hold for 3 seconds. Bluetooth will be disabled. To enable it, perform the same operation.

Enable: The Bluetooth indicator flashes twice and remains lit.

Disable: The Bluetooth indicator flashes twice and turns off.

Flashes from the left in order

Indicator display

Note

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MusicCast - WX-010 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MusicCast - WX-010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info