Bedienungsanleitung Yamaha MX88 (Seite 47 von 56) (Englisch)

707407

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

MX49 MX61 MX88 Owner’s Manual

Appendix

Troubleshooting

No sound? Wrong sound? When a problem like this occurs, please check the following points before assuming that the

product is faulty. Many problems can be solved by executing the Factory Set operation (page 11), after backing up your

data to an USB flash memory (page 32). If the problem persists, consult your Yamaha dealer.

No Sound.

 Is this instrument properly connected to related external equipment (e.g., amplifier, speaker, headphone) via audio cables?

Since this instrument has no built-in speakers, you will need an external audio system or a set of stereo headphones to properly monitor it

(page 9*).

 Is the power of this synthesizer and any external equipment connected to it turned on?

 Have you made all the appropriate level settings—including the Master Volume on this instrument and the volume settings on any

connected external equipment?

If a Foot Controller is connected to the [FOOT CONTROLLER] jack, operate the Foot Controller and check the sound volume.

 Check the Local Control parameter in the Utility display.

When this instrument is used by itself and this parameter is set to off, no sound is produced even if you play the keyboard.

 Check the Direct Monitor Switch parameter in the Utility display.

When this instrument is used by itself and this parameter is set to off, no sound is produced even if you play the keyboard.

 Are the MIDI volume or MIDI expression settings too low when using an external controller?

 Are the effect and filter settings appropriate?

If you are using the filter, try changing the cutoff frequency. Some cutoff settings may filter out all of the sound.

 Are the volume or expression settings too low?

No sound from the [AUX IN] jack.

 Is the volume of the connected audio device set to a value other than “0”?

Cannot play audio data.

 Is the volume for the audio data set to a value other than “0”?

 Is the format of the audio data correct?

This instrument can play only stereo WAVE (.wav) files of 44.1kHz/16-bit.

Playback continues without stopping.

 When the [ARP] button is turned on, press it so that its lamp is turned off.

 When playing back Rhythm Pattern or Song data of the USB flash memory, press the [J] (Stop) button.

The instrument is automatically turned off even if no operation is done.

 Is the Auto Power Off function enabled?

If necessary, disable this function or change the amount of time that elapses before the power is automatically turned off.

[UTILITY]  Select “02:MIDI”  [ENTER]  “LocalCtrl”

[UTILITY]  Select “01:General”  [ENTER]  “DirectMonitor”

[EDIT]  Select “02:Part”  [ENTER]  Select “02:Filter/EG”  [ENTER]

[EDIT]  Select “02:Part”  [ENTER]  Select “05:Voice Insert Eff”/“05:DrumKit Insert Eff”  [ENTER]

[UTILITY]  Select “01:General”  [ENTER]  “MasterVolume”

[EDIT]  Select “01:Common”  [ENTER]  Select “05:General”  [ENTER]  “Volume”

[PART SELECT]  “Volume”

[UTILITY]  Select “01:General”  [ENTER]  “WAV Volume”

[UTILITY]  Select “01:General”  [ENTER]  “A utoOff”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MX88 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MX88

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info