555181
2
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
2
To mount the speaker on a wall by using
the attached mounting bracket
Fasten screws into a firm wall or wall support as shown in
the figure, and hang the holes of the mounting bracket on
the protruding screws.
* Make sure that the screws are securely caught by the
narrow parts of the holes.
WARNING
This speaker weighs 5.5 kg (12 lbs. 2 oz.). Do not
mount it on thin plywood or a wall with soft surface
material. If mounted, the screws may come out of the
flimsy surface and the speaker may fall. This
damages the speaker or causes personal injury.
Do not install the speaker to a wall with nails,
adhesives, or any other unstable hardware. Long-
term use and vibrations may cause it to fall.
To avoid accidents resulting from tripping over loose
speaker cable, fix it to the wall.
Before making connections, make sure that
the amplifier is switched off.
Connections
Connect the screw-type input terminals at the rear of the
speaker to the speaker output terminals of the amplifier
(or receiver) with the speaker cable.
Connect the (+) terminals on the amplifier (or receiver)
and the speaker using one side of the cable. Connect the
() terminals on both components using the other side of
the cable.
Connect the speaker to the center terminals of the
amplifier (or receiver) making sure not to reverse the
polarity (+, ). If the speaker is connected with reversed
polarity, the sound will be unnatural and lack bass.
How to Connect:
1 Remove the insulation coating at the extremity of each
speaker cable by twisting the coating off.
2 Loosen the terminal knob.
3 Insert the bare wire.
4 Tighten the knob and secure the cable. Test the
firmness of the connection by pulling lightly on the
cable at the terminal.
Note
Do not let the bare speaker wires touch each other to avoid
damaging the speaker or the amplifier, or both of them.
[Using a Banana Plug]
1 Remove the speaker terminal cover by gently pulling it
toward you.
2 Tighten the terminal knob.
3 Simply insert the banana plug into the terminal.
CONNECTIONS TO YOUR AMPLIFIER
Tapping screw (3.5 – 4 mm)
(Available at the hardware
store)
Min.
20 mm
3 mm
Wall/ Wall Support
SPEAKERS
A
B
L
R
+
+
Loosen
Tighten
Black (
)
Red (+)
Speaker (R)
Speaker (L)
Amprifier or
Receiver
Speakers output
terminals of the
amplifier
Good No Good
Banana Plug
05AGHO2CIG6W GUFC[/CTEJ 2/
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha NS-333 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info