Bedienungsanleitung Yamaha NS-BP110 (Seite 2 von 12) (Deutsch, Englisch, Französisch, Spanisch)

554955

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

2 En

English

• Install the speakers in a cool, dry, clean, stable and horizontal

place.

• To avoid electric shock, fire, injury, damage to the speakers, and

discoloration of the cabinet, install away from windows, heat

sources, sources of excessive vibration, dust, moisture, cold, rain,

water, falling objects, noise sources (transformers, motors, etc.)

and direct sunlight.

• Do not insert a hand or object into the port or pick up the speaker

by holding the port, as it may cause personal injury or damage to

the speaker.

• Any time you note distortion, reduce the volume control on your

receiver to a lower setting. Never allow your receiver to be driven

into “clipping”. Otherwise the speakers may be damaged.

• When using a receiver with a rated output power higher than the

nominal input power of the speakers, care should be taken never

to exceed the speakers’ maximum input.

• Do not attempt to clean the speakers with chemical solvents as

this might damage the finish. Use a clean, dry cloth.

• Do not attempt to modify or fix the speakers. Contact qualified

Yamaha service personnel when any service is needed. The cabi-

net should never be opened for any reasons.

• Secure placement or installation is the owner’s respon-

sibility. Yamaha shall not be liable for any accident

caused by improper placement or installation of speak-

ers.

Check that the following items are included.

Speaker cable (2 m) x 2 / Front cover x 2

To attach the front cover, line up the

three holes on the inner surface of the

cover with the three corresponding pegs

on the speaker and push gently.

When the cover is removed, be sure not to touch the

speaker units with your hands or to exert excessive force

with tools.

BEFORE MAKING CONNECTIONS, MAKE SURE THAT

THE RECEIVER IS SWITCHED OFF.

When this unit is connected to the receiver, refer also to the owner’s

manual supplied with the receiver.

See page 1 for the connection method.

• Place the speakers on a sturdy, vibration-free surface. You may

not be able to obtain good bass quality when the speakers are

placed directly on the floor. Put a block, etc. under the speakers.

• Better stereo images will be obtained when the speakers are

slightly angled in towards the listening position.

Placing this unit too close to a CRT TV set might happen

impair picture color or create a buzzing noise. Should

this happen, move the speaker away from the TV set.

NS-BP110 only

You can also use the screw holes on the bottom of the NS-BP110 for

installing the speakers on commercially available speaker stands.

• Before installing, please refer to the instruction manual of the

speaker stand.

Type ..............................................2-way bass-reflex speaker system

Non-magnetic shielding Type

Driver........................................................... 10 cm (4”) cone woofer

2.5 cm (1”) balanced dome tweeter

Impedance.................................................................................... 6Ω

Frequency Response................................. 60 Hz to 50 kHz (-10 dB)

100 kHz (-30 dB)

Nominal Input Power ................................................................30 W

Maximum Input Power..............................................................90 W

Sensitivity.................................................................84 dB/2.83 V/m

Crossover Frequency ................................................................8 kHz

Dimensions (W x H x D)

<NS-BP100> .................................................. 123 x 192 x 294 mm

(4-13/16” x 7-9/16” x 11-9/16”)

<NS-BP110> .................................................. 123 x 192 x 296 mm

(4-13/16” x 7-9/16” x 11-5/8”)

Weight

<NS-BP100> .................................................. 2.1 kg (4 lbs. 10 oz.)

<NS-BP110> .................................................... 2.3 kg (5 lbs. 1 oz.)

* Specifications are subject to change without notice due to

product improvements.

* Care should be taken not to exceed the input power values noted

above.

PRECAUTIONS

ACCESSORIES

ATTACHING THE FRONT COVER

Note

CONNECTION TO YOUR RECEIVER

PLACING THE SPEAKERS

Note

ATTACHING THE SPEAKER STANDS

SPECIFICATIONS

A screw with a diameter of 4

mm can be used

(Hole depth: 10 mm, 3/8”)

NS-BP_100110_ex.fm 2 ページ２００８年１０月１１日土曜日午後３時５８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha NS-BP110 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info