Bedienungsanleitung Yamaha NS-P285 (Seite 7 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

555585

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

4 En

English

■ Operating the speaker terminals

1 Press and hold the terminal tab.

2 Insert the bare wire.

3 Release the tab so that it closes securely on the

bare wire, not the insulation.

4 Test the security of the connection by pulling

gently on the cable.

Notes

• Make sure the bare wires do not touch each other, as

this could damage the speaker or the amplifier.

• If the connections are faulty, you will hear no sound

from the speakers.

■ Connecting the speakers

Connect each speaker to the appropriate speaker

terminals on your amplifier by using the cables you

prepared earlier. See the “Connection diagram” on

page 3 for reference.

Make sure you connect the speakers with the correct

polarity—positive (+) terminals to positive (+)

terminals, and negative (–) terminals to negative (–)

terminals. If you get them crossed over, the sound will

be unnatural and lack bass.

In your AV receiver’s speaker size settings, specify

small (or “S”) for all of the NS-P285 speakers.

If you’re connecting the subwoofer to a Yamaha DSP

amplifier or AV receiver, connect to its SUBWOOFER

or LOW PASS output.

Connecting the power cables

Once you’ve completed all of the speaker and

subwoofer connections, plug the subwoofer, amplifier,

and your other AV components into suitable AC wall

outlets.

1 Power indicator

Lights up when the POWER switch is set to ON;

goes off when the POWER switch is set to OFF.

2 INPUT jack

Input jack for connecting the line-level subwoofer

output on your amplifier.

3 VOLUME control

Adjusts the volume of the subwoofer. Turn it

clockwise to increase the volume;

counterclockwise to decrease the volume.

4 POWER switch

Set this to ON to turn on the subwoofer. Set it to

OFF to turn off the subwoofer.

Setting the subwoofer volume

The very first time you use the subwoofer, you need to

set the volume balance between the subwoofer and the

front speakers as follows.

1 Turn on your other AV components.

2 Set the subwoofer’s VOLUME control to

minimum (0).

3 Set the subwoofer’s POWER switch to ON.

The power indicator on the rear panel lights up.

4 Play a audio source that contains low-

frequency bass sounds. Set the amplifier’s

volume control to a suitable level.

5 Turn the subwoofer’s VOLUME control up

gradually until you achieve a good balance

between the subwoofer and the other

speakers.

Notes

• Once the subwoofer volume has been set, you can

leave the subwoofer’s VOLUME control set as it is

and use your amplifier’s volume control to adjust the

volume of the entire system.

Positive (+)

Negative (–)

Note: Make sure the

terminal is gripping

the bare wire, not

the insulation.

Using the Subwoofer

Rear panel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha NS-P285 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info