Bedienungsanleitung Yamaha NS-SW300 (Seite 7 von 148) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

555562

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

4 En

English

CONTROLS AND THEIR FUNCTIONS

1 Indicator

2 VOLUME control ( page 11)

Adjusts the volume level. Turn the control clockwise to increase the volume, and

counterclockwise to decrease the volume.

3 STANDBY/ON switch

While the POWER switch is ON, press this switch to turn on the power to the

subwoofer. The indicator will light up green. Press the switch again to turn off the

power to the subwoofer. The indicator will turn off.

4 Port ( page 1)

Outputs super-bass sound.

5 INPUT2 (NORMAL) terminals ( page 5)

Used to input line level signals from the amplifier.

6 INPUT3 (LFE) terminal ( page 6)

If your amplifier (or receiver) can cut off high frequencies from signals sent to the

subwoofer, connect the amplifier to the subwoofer’s INPUT3 (LFE) terminal.

The HIGH CUT control # has no effect on signals input to the INPUT 3 LFE terminal.

7 AUTO STANDBY (HIGH/LOW/OFF) switch ( page 10)

This switch is originally set to the OFF position. By setting this switch to the HIGH or

LOW position, the subwoofer’s automatic power-switching function operates. If you

do not need this function, leave this switch in the OFF position.

Note

Be sure to set the POWER switch to OFF before you set the AUTO STANDBY switch.

8 PHASE switch ( page 11)

This switch is to be set to the REV (reverse) position. However, depending on your speaker

system or listening conditions, there may be a case when better sound quality is obtained by

setting this switch to the NORM (normal) position. Select the best position by ear.

9 B.A.S.S. (Bass Action Selector System) switch (NS-SW300 only)

( page 11)

When this switch is set to MUSIC, the bass sound in audio

software is well reproduced. When the switch is set to

MOVIE, the bass sound in video software is well reproduced.

) SYSTEM CONNECTOR jack ( page 10)

Connect the supplied system control cable here. If you use the system control cable to

connect a subwoofer to a Yamaha component (that features a system connector jack),

turning on or off the power to the connected component automatically turns the

subwoofer on or off.

! OUTPUT (TO SPEAKERS) terminals ( page 7)

Can be used for connecting to the main speakers. Signals at the INPUT1 terminals are

sent to these terminals.

@ INPUT1 (FROM AMPLIFIER) terminals ( page 7)

Used to connect the subwoofer with the speaker terminals of the amplifier.

# HIGH CUT control ( page 11)

Adjusts the high frequency cut off point.

Frequencies higher than the frequency selected by this

control are all cut off (and not output).

$ POWER switch

During normal usage, set this switch to ON. If you plan not to use the subwoofer for a long

period of time, set the switch to OFF.

Green:

Red:

Off:

The subwoofer is turned on.

The Automatic power-switching function has activated, and the subwoofer

is in standby mode.

The subwoofer is turned off.

The subwoofer uses a small amount of power in standby mode.

* One graduation

of this control

represents 10 Hz.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha NS-SW300 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info