669113
84
Zoom out
Zoom in
Vorherige Seite
1/94
Nächste Seite
82
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
Appendix
The maximum of 255 “banks” of data has been exceeded (one pad contains one “bank”).
Clear all unnecessary pads and voice data before attempting to sample more data.
You have attempted to map or tune a pad or entering an original voice name that contains
no sampled voice data.
You have attempted to clear, record, or edit a pre-programmed disk voice file. In some
cases pre-programmed sampled voices (“Protected Voices”) can only be loaded.
You have attempted to map a pad to key to which another pad is already mapped. Map
either pad to a different key.
The wave RAM memory is full and can accept no more sampled voice data (the wave RAM
is 1,020 kilobytes). Clear all unnecessary pads and voice data before attempting to sample
more data.
You have inserted the wrong disk or a disk that does not contain the required data. Large
sampled voice data files may span more than one disk, and these must be inserted in the
correct order when loading the file. Check the disk number and try again.
No Bank
No Wave Data
Digital Sampling-related Error Messages (PSR-2700)
Wave Ram Full
Protected Voice
Same Note
Wrong Disk
Other Error Messages
You have pressed a button that can not be used in the current mode. Read the instructions
for the function you are using carefully, and use appropriate function button.
IllegalOperation
The PSR-1700/2700 recording memory has become full while recording Song Memory,
Custom Accompaniment, or Multi Pad data. Save data you want to keep to disk and clear
all unnecessary data from memory to make more room.
Memory Full
System Reset Procedure
All internal memory settings are retained in memory even when the power switch is turned OFF as long as a
good set of backup batteries is present or the AC plug is connected. You can, however, restore the factory default
settings by following the procedures outlined below.
–+
RESET
POWER
ON/ OFF
ZPress the [POWER] switch to turn the PSR-1700/PSR-2700 power OFF.
XTurn the power back ON while holding both the [+] and [–] buttons.
Backup RAM Clear will appear on the LCD display panel while the
data is being reset.
IMPORTANT
Executing the System Reset function will erase all internal
memory settings
84

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha PSR-1700 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info