Bedienungsanleitung Yamaha PSR-262 (Seite 8 von 64) (Englisch)

635584

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Setting Up

This section contains information about setting up your PSR-262 for playing. Make sure to

read this section carefully before using the instrument.

Power Requirements

Although the PSR-262 will run either from an optional AC adaptor or batteries,

Yamaha recommends use of an AC adaptor whenever possible. An AC adaptor is

more environmentally friendly than batteries and does not deplete resources.

■

Using an AC Power Adaptor • • • • • • • • • • • • • • • • • • • • • • • • •

To connect your PSR-262 to a wall socket, you will need the optionally available

Yamaha PA-3B Power Adaptor. Use of other AC adaptors could result in damage

to the instrument, so be sure to ask for the right kind. Connect one end of the

adaptor to the DC IN 10-12V jack on the rear panel of your PSR-262, and the

other end to a suitable electrical outlet.

■

Using Batteries • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

●

Inserting Batteries

Turn the instrument upside-down and remove the battery compartment lid. Insert

six 1.5-volt size “D” (SUM-1, R-20 or equivalent) batteries as shown in the illus-

tration, making sure that the positive and negative terminals are properly aligned,

and replace the lid.

●

When the Batteries Run Down

When the batteries run low and the battery voltage drops below a certain level, the

PSR-262 may not sound or function properly. As soon as this happens, replace

them with a complete set of six new batteries.

Turning On the Power

With the AC power adaptor connected or with batteries installed, simply press the

STANDBY switch until it locks in the ON position. When the instrument is not in

use, be sure to turn the power off. (Press the switch again so that it pops up.)

• Use ONLY a Yamaha PA-3B AC

Power Adaptor (or other adap-

tor speciﬁcally recommended

by Yamaha) to power your

instrument from the AC mains.

The use of other adaptors may

result in irreparable damage to

both the adaptor and the PSR-

262.

• Unplug the AC Power Adaptor

when not using the PSR-262,

or during electrical storms.

BATTERIES 1.5V

• Never mix old and new batter-

ies or different types of batter-

ies (e.g., alkaline and

manganese).

• To prevent possible damage

from battery leakage, remove

the batteries from the instru-

ment if it is not to be used for a

long time.

• Even when the switch is in the

“STANDBY” position, electric-

ity is still ﬂowing to the instru-

ment at the minimum level.

When you are not using the

PSR-262 for a long time, make

sure you unplug the AC power

adaptor from the wall AC out-

let, and/or remove the batteries

from the instrument.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha PSR-262 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info