Bedienungsanleitung Yamaha PSR-340 (Seite 111 von 128) (Englisch)

566139

111

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

111

A strange “flanging” or “doubling” sound

occurs when using the PortaTone with a

sequencer. (This may also sound like a “dual”

layered sound of two voices, even when Dual

is turned off.)

• If you are routing the MIDI OUT on the PortaTone to a

sequencer and back to the MIDI IN, you may want to set Local

Control (page 107) to “off” to avoid MIDI “feedback.”

• When using the accompaniment with a sequencer, set MIDI

Echo (or the relevant control) to “off.” (Refer to the owner’s

manual of your particular device and/or software for details.)

The footswitch seems to produce the opposite

effect. For example, when using the footswitch

for sustain, pressing the footswitch cuts off the

sound and releasing it sustains the sounds.

The polarity of the footswitch is reversed. Make sure that the

footswitch plug is properly connected to the FOOT SWITCH jack

before turning on the power.

The AWM tone generation method uses multiple recordings

(samples) of an instrument across the range of the keyboard;

thus, the actual sound of the voice may be slightly different from

note to note.

The sound of the voice changes from note to

note.

Problem Possible Cause and Solution

TROUBLESHOOTING

DATA BACKUP & INITIALIZATION

Except for the data listed below, all PSR-340 panel settings are reset to their initial settings

whenever the power is turned on. The data listed below are backed up — i.e. retained in

memory — as long as an AC adaptor is connected or a set of batteries is installed.

• User Song Data • Metronome Volume

• User One Touch Setting Data • Touch On/Off

• One Touch Setting Bank Number • Touch Sensitivity

• EZ Chord Data • Split Point

• EZ Chord Bank Number Data • Accompaniment Split Point

• Smart Chord Number • Footswitch Assign Function

• Style 101 Data

CLr

Backup

VOICE

STYLE

CAUTION

• All one touch setting

(user) and song memory

data, plus the other settings

listed above, will be erased

and/or changed when the

data initialization proce-

dure is carried out.

• Carrying out the data

initialization procedure will

usually restore normal

operation if the PSR-340

freezes or begins to act

erratically for any reason.

Data Initialization

All data can be initialized and restored to the factory preset condition by turning on the

power while holding the highest (rightmost) white key on the keyboard. “CLr Backup” will

appear briefly on the display.

109

Nothing happens or nothing seems to

function, even when pressing a panel button.

For example, pressing the DEMO button does

not start the Demo song, or playing the

keyboard does not produce any sound.

One of the the disk-related displays (SAVE, LOAD, DELETE, or

FORMAT) is shown. Exit from the display by pressing the SAVE

button (from the SAVE display), the LOAD button (from the

LOAD display), or the UTILITY button (from the DELETE or

FORMAT displays).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha PSR-340 Seite 111

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha PSR-340

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info