Bedienungsanleitung Yamaha PSR-8000 (Seite 15 von 206) (Englisch)

635400

Zoom out

Zoom in

Vorherige Seite

1/206

Nächste Seite

Although the PSR-8000 can be connected to a personal computer via the MIDI IN/OUT connectors and a MIDI

interface, the TO HOST connector and HOST SELECT switch allow direct connection to Apple Macintosh or IBM

PC/AT personal computers for sequencing and other music applications without the need for a separate MIDI

interface.

• When using the [TO HOST] terminal of the PSR-8000, first turn the power off on both the PSR-8000 and the computer before

connecting the cable. After connecting the cable, turn the power of the computer on first, then the PSR-8000.

• When not using the [TO HOST] terminal of the PSR-8000, make sure the cable is disconnected from the [TO HOST] terminal. If

the cable is left connected, the PSR-8000 may not function properly.

• When the HOST SELECT switch is set to “Mac”, “PC-1”, or “PC-2, no data transfer occurs via the MIDI connectors. To use the MIDI

connectors for connection via a standard MIDI interface, set the HOST SELECT switch to “MIDI”.

• No MIDI or TO HOST transmission or reception occurs in the SAMPLING mode.

7 TO HOST Connector & HOST SELECT Switch ...........................................................................................

● Connecting to an Apple Macintosh Series Computer ..................................................................

Connect the TO HOST connector of the PSR-8000 to the modem or printer port on your Macintosh, depending

on which port your MIDI software is using for MIDI data communication, using a standard Macintosh 8-pin system

peripheral cable. Set the HOST SELECT switch to the “Mac” position.

You may also have to make other MIDI interface settings on the computer side, depending on the type of software

you use (refer to your software owner’s manual). In any case the clock speed should be set to 1 MHz.

● Connecting to an IBM-PC/AT Series Computer ...................................................................................

Connect the TO HOST connector of the PSR-8000 to the RS-232C port on your IBM computer, using a standard

8-pin MINI DIN → 9-pin D-SUB cross cable. Set the HOST SELECT switch to the “PC-2” position.

Refer to your software owner’s manual for information on any settings you might have to make on the computer

side.

2 (HSK i)1

1 (HSK 0)2

5 (RxD-)3

MINI DIN

8-PIN

4 GND4

3 (TxD-)5

8 (RxD+)6

7 (GP i)7

6 (TxD+)8

MINI DIN

8-PIN

“Mac” Cable Connections

• 8-pin system peripheral cable.

• Data transfer rate: 31,250 bps.

Apple Macintosh

Series Computer

Set to the “Mac”

position.

TO HOST

PC-1 PC-2

MIDIMac

8 (CTS)1

7 (RST)2

2 (RxD)3

4 5 (GND)

3 (TxD) 5

MINI DIN

8-PIN

D-SUB

9-PIN

“PC-2” Cable Connections

• 8-pin mini DIN → 9-pin D-SUB cable.

• Data transfer rate: 38,400 bps.

IBM-PC/AT

Series Computer

Set to the “PC-2”

position.

TO HOST

PC-1 PC-2

MIDIMac

Connections & Music Stand

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha PSR-8000 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha PSR-8000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info