Bedienungsanleitung Yamaha RX-A810 (Seite 113 von 130) (Englisch)

492654

113

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

En 113

Audio

Problem Cause Remedy

No sound.

Another input source is selected. Select an appropriate input source with the input selection keys

Signals that this unit cannot reproduce are being input.

Some digital audio formats cannot be played back on this unit. To check the

audio format of the input signal, use “Audio Signal” in the “Information” menu

(p.102).

The cable connecting this unit and playback device is defective. If there is no problem with the connection, replace with another cable.

The volume cannot be increased.

The maximum volume is set. Use “Max Volume” in the “Setup” menu to adjust the maximum volume (p.94).

Any device connected to the output jacks of this unit is not turned

on. (This may happen due to the nature of AV receivers.)

Turn on all devices connected to the output jacks of this unit

No sound is heard from a specific

speaker.

The playback source does not contain corresponding channel

signals.

To check it, select “7ch Stereo” (p.45).

The sound program/decoder currently selected does not use the

corresponding speaker.

To check it, select “7ch Stereo” (p.45).

Audio output of the corresponding speaker is disabled.

Perform “Auto Setup” (p.36) or use “Configuration” in the “Setup” menu to change

the speaker setting (p.91).

The volume of the corresponding speaker is too low.

Perform “Auto Setup” (p.36) or use “Level” in the “Setup” menu to adjust the

speaker volume (p.93).

The speaker cable connecting this unit and corresponding

speaker is defective.

If there is no problem with the connection, replace with another speaker cable.

The corresponding speaker is malfunctioning.

To check it, replacing with another speaker. If the problem persists, this unit may

be malfunctioning.

No sound is heard from the surround

back speaker.

The extended surround is disabled.

Use “Extended Surround” in the “Option” menu to select a decoder to be used

(p.79).

No sound is heard from the subwoofer.

The playback source does not contain LFE or low-frequency

signals.

To check it, set “Extra Bass” in the “Setup” menu to “On”, to output the front

channel low-frequency components from the subwoofer (p.92).

Subwoofer output is disabled.

Perform “Auto Setup” (p.36) or set “Subwoofer” in the “Setup” menu to “Use”

(p.92).

The subwoofer is turned off by the auto-standby function on it. Disable the auto-standby function of the subwoofer or adjust its sensitivity level.

No sound from the playback device

(connected to this unit with HDMI).

The TV does not support HDCP (High-bandwidth Digital Content

Protection).

To check it, use “Video Signal” in the “Information” menu (p.102).

This unit is set not to output audio input through HDMI jacks from

the SPEAKERS terminals.

In “Audio Output” in the “Setup” menu, set “Amp” to “On” (p.97).

The number of devices connected to the HDMI OUT jack is over

the limit.

Disconnect some of the HDMI devices.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-A810 Seite 113

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-A810

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info