Bedienungsanleitung Yamaha RX-V1000RDS (Seite 77 von 85) (Englisch)

558947

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

EnglishINTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TROUBLESHOOTING

Refer to the chart below when the unit does not function properly. If the problem you are experiencing is not listed

below or if the instruction below does not help, set this unit in the standby mode, disconnect the power cord, and

contact the nearest authorized YAMAHA dealer or service center.

■ General

Problem Cause Remedy

Refer to

page

The unit fails to turn on

when STANDBY/ON (or

SYSTEM POWER) is

pressed, or enters in the

standby mode soon

after the power has

been turned on.

The power cord is not connected or the plug

is not completely inserted.

Firmly connect the power cord.

The IMPEDANCE SELECTOR switch

on the rear panel is not fully set to the

left or right position.

Set the switch fully to the left or right

position when the unit is in the standby

mode.

The protection circuitry has been

activated.

Make sure all speaker wire connections on

this unit and on all speakers are secure and

that the wire for each connection does not

touch anything other than its respective

connection.

No sound and/or no

picture.

Incorrect input or output cable connections. Connect the cables properly. If the problem

persists, the cables may be defective.

An appropriate input source has not

been selected.

Select an appropriate input source with

INPUT l / h or 6CH INPUT (or the input

selector buttons).

The speaker connections are not secure. Secure the connections.

The main speakers to be used have not

been selected properly.

Select the main speakers with SPEAKERS A

and/or B.

The volume is turned down. Turn up the volume.

The sound is muted. Press MUTE or any operation buttons of this

unit to cancel a mute and adjust the volume.

Digital signals other than PCM audio,

Dolby Digital or DTS signal which this

unit cannot reproduce are being input to

this unit by playing a CD-ROM, etc.

Play a source whose signals this unit can

reproduce.

No picture. There is no S-video connection between this

unit and the video monitor, although

S-video signals are being input to this unit.

Connect the monitor’s S-video input jack to

this unit’s S VIDEO MONITOR OUT jack.

The sound suddenly

goes off.

The protection circuit has been activated

because of a short circuit, etc.

Check the IMPEDANCE SELECTOR

switch is set to the appropriate position and

then turn the unit back on.

The sleep timer has functioned. Turn on the power, and play the source

again.

Only the speaker on one

side can be heard.

Incorrect cable connections. Connect the cables properly. If the problem

persists, the cables may be defective.

Incorrect setting of “3 L/R BALANCE”

on the SET MENU.

Adjust it to the appropriate position.

16, 17

12 – 15

16, 17

—

14, 15

12 – 17

APPENDIX

Check the speaker wires are not touching

each other and then turn the unit back on.

The sound is muted. Press MUTE or any operation buttons of this

unit to cancel a mute and adjust the volume.

16, 17

0113V1000RDS_75-80_EN 9/5/0, 4:44 PM75

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V1000RDS Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info