Bedienungsanleitung Yamaha RX-V2400 (Seite 55 von 91) (Englisch)

558954

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

English

SET MENU

ADVANCED

OPERATION

■ Speaker distance SP DISTANCE

Use this feature to manually input the distance of each

speaker and adjust the delay applied to respective channel.

Ideally, each speaker should be the same distance from the

main listening position. However, this is not possible in

most home situations. Thus, a certain amount of delay

must be applied to the sound from each speaker so that all

sound will arrive at the listening position at the same time.

To access these parameters, select:

MANUAL SETUP > SOUND MENU > SP DISTANCE >

Unit UNIT

Choices: meters (m), feet (ft)

Initial setting:

U.S.A. and Canada models: feet (ft)

Other models: meters (m)

• Select meters to input speaker distances in meters.

• Select feet to input speaker distances in feet.

Speaker distances

Choices: 0.3 to 24.00 m (1 to 80 ft)

• FRONT L adjusts the distance of the front left speaker.

Initial setting: 3.0 m (10.0 ft)

• FRONT R adjusts the distance of the front right

speaker. Initial setting: 3.0 m (10.0 ft)

• CENTER adjusts the distance of the center speaker.

Initial setting: 3.0 m (10.0 ft)

• SURR L adjusts the distance of the surround left

speaker. Initial setting: 3.0 m (10.0 ft)

• SURR R adjusts the distance of the surround right

speaker. Initial setting: 3.0 m (10.0 ft)

• SB adjusts the distance of the surround back left

speakers. Initial setting: 2.10 m (7.0 ft)

• SWFR adjusts the distance of the subwoofer. Initial

setting: 3.0 m (10.0 ft)

■ Graphic equalizer GRAPHIC EQ

Use this feature to select parametric (PEQ) or graphic

equalizer (GEQ).

To access these parameters, select:

MANUAL SETUP > SOUND MENU > GRAPHIC EQ >

Equalizer select EQ SELECT

Choices: PEQ, GEQ

• Select PEQ to use the equalizer adjusted in auto setup.

• Select GEQ to adjust the built-in 7-band graphic

equalizer so that the center, surround L/R and surround

back L/R speakers tonal quality matches that of the left

and right front speakers.

Choices: –6 to +6 (dB)

You can adjust 7 frequency bands: 63Hz, 160Hz, 400Hz,

1kHz, 2.5kHz, 6.3kHz, 16kHz

■ Low-frequency effect level LFE LEVEL

Use to adjust the output level of the LFE (low-frequency

effect) channel according to the capacity of your

subwoofer or headphones. The LFE channel carries low-

frequency special effects which are only added to certain

scenes. This setting is effective only when this unit

decodes Dolby Digital or DTS signals.

To access these parameters, select:

MANUAL SETUP > SOUND MENU > LFE LEVEL

Choices: –20 to 0 (dB)

Speaker SPEAKER

Select to adjust the speaker LFE level.

Headphone HEADPHONE

Select to adjust the headphone LFE level.

Depending on the settings of LFE LEVEL, some signals may not

be output from the SUBWOOFER jack.

. UNIT;;;;;;meters

FRONTL;;;;2.30m

FRONTR;;;;2.30m

CENTER;;;;;2.00m

: Up/Down

: Adjust

-/+

C)SP

DISTANCE

Note

. CHANNEL;;FRONT L

63Hz 0dB

160Hz 0dB

400Hz 0dB

1kHz 0dB

2.5kHz 0dB

6.3kHz 0dB

16kHz 0dB

D)GRAPHIC

. SPEAKER;;;;;;0dB

HEADPHONE;;;;0dB

/ : Up/Down

-/+ : Adjust

E)LFE

LEVEL

01EN00_RX-V2400RDS_EN.book Page 53 Thursday, November 6, 2003 11:49 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V2400 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V2400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info