Bedienungsanleitung Yamaha RX-V3067 (Seite 139 von 166) (Englisch)

516915

139

Zoom out

Zoom in

Vorherige Seite

1/166

Nächste Seite

En 139

APPENDIX

Refer to the table below when this unit does not function properly.

If the problem you are experiencing is not listed below, or if the instructions below do not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service

center.

General

Troubleshooting

Problem Cause Remedy

See

page

The power will not

turn on.

The protection circuitry operated

3 times consecutively.

As a safety precaution, when the protection

circuitry operates 3 times consecutively, the

capability to turn on the power is disabled.

Contact your nearest Yamaha dealer or

service center to request repair.

—

The unit enters

standby mode soon

after the power is

turned on.

The power cable is not completely

inserted.

Connect the power cable properly to an AC

wall outlet.

—

(When this unit is turned back on

and “CHECK SP WIRES!” is

displayed.) The protection

circuitry has been activated

because this unit was turned on

while a speaker cable was shorted.

Make sure that all speaker cables between

this unit and speakers are connected

properly.

This unit cannot be

turned off or does

not work properly.

The internal microcomputer is

hung-up due to an external electric

shock (such as lightning or

excessive static electricity) or by a

drop in power supply voltage.

Disconnect the power cable from the AC

wall outlet, wait about 30 seconds and then

plug it in again.

—

The batteries in the remote control

may have lost their charge.

Replace all batteries. 13

The unit enters

standby mode.

The protection circuitry has been

activated because of a short circuit,

etc.

Check that the speaker with an impedance

of at least 6 Ω.

—

Check that the speaker impedance settings

are correct.

Check that the speaker wires are not

touching each other, then turn the unit back

on.

—

The sleep timer has turned off the

unit.

Turn on the unit, and play the source again. —

After display of a

countdown on the

front panel, the unit

goes into standby

mode.

If you do not use take any action,

the Auto Power Down function

operates.

Turn on the unit, and play the source again. —

In the Setup menu “Auto Power Down”

(“Function” → “Auto Power Down”),

increase the time until switching to standby

mode, or turn off the Auto Power Down

function.

112

No sound. Incorrect input or output cable

connections.

Connect the cables properly. If the problem

persists, the cables may be defective.

Speaker connections are not

secure.

Secure the connections. 22

The HDMI components connected

to the unit do not support the

HDCP copy protection standards.

Connect HDMI components that support the

HDCP copy protection standards.

—

The audio input into the device is

set to playback through the TV.

In the Setup menu, set the “Amp” of “Audio

Output” (“HDMI” → “Audio Output” →

“Amp”) to “On.”

107

No appropriate input source has

been selected.

Select an appropriate input source with

Input selector.

The volume is turned down or

muted.

Turn up the volume. —

Signals that this unit cannot

reproduce are being input from a

source component, such as a CD-

ROM.

Use an input source that has signals that can

be reproduced on this unit.

—

Problem Cause Remedy

See

page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V3067 Seite 139

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V3067

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info