Bedienungsanleitung Yamaha RX-V3800 (Seite 69 von 165) (Englisch)

464156

Zoom out

Zoom in

Vorherige Seite

1/165

Nächste Seite

Recording

67 En

BASIC

OPERATION

English

Recording adjustments and other operations are performed from the recording components. Refer to the operating

instructions for those components.

• When this unit is set to the standby mode, you cannot record between other components connected to this unit.

• TONE CONTROL (see page 51) and the volume settings, the speaker level (see page 91) and the sound field programs (see page 45)

do not affect recorded material.

• The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded.

• Digital signals input at the DIGITAL INPUT jacks are not output at the analog audio OUT (REC) jacks for recording. Likewise,

analog signals input at the AUDIO IN jacks are not output at the DIGITAL OUTPUT jack. Therefore, if your source component is

connected to provide only digital or analog signals, you can only record digital or analog signals.

• A given input source is not output on the same OUT (REC) channel.

• S-video and composite video signals pass independently through the video circuits of this unit. Therefore, when recording or dubbing

video signals input from a video source component that provides only an S-video or a composite video signal, you can record only an

S-video or a composite video signal on your VCR.

• The analog audio and video signals input at the DOCK terminal can be output at the analog audio OUT (REC) jacks and DVR or VCR

OUT jacks for recording.

• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright

laws.

Do a test recording before you start an actual recording.

1 Turn on all the connected components.

2 Press

REC OUT/ZONE2 until the

RECOUT indicator lights up in the front panel

display.

This unit in the recording source selecting mode.

3 Rotate the

PROGRAM to select the source

component you want to record from.

Carry out the operation while the RECOUT indicator

is lit.

Select “SOURCE” to record the currently selected input

source.

4 Start playback on the selected source

component or select a broadcast station.

5 Start recording on the recording component.

Recording

Caution

The DTS signal is a digital bitstream. Attempting to digitally record the DTS bitstream will result in noise being

recorded. Therefore, if you want to use this unit to record sources encoded in DTS, the following considerations and

adjustments need to be made. To play DTS-encoded DVDs and CDs (when using a digital audio connection) on your

DTS-compatible player, follow its operating instructions to make a setting so that the analog signal will be output

from the player.

Notes

If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture

itself may be disturbed due to those signals.

RECOUT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V3800 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V3800

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info