Bedienungsanleitung Yamaha RX-V565 (Seite 23 von 332) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

464173

Zoom out

Zoom in

Vorherige Seite

1/332

Nächste Seite

19 En

Optimizing the speaker setting for your listening room (YPAO)

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Flat

This adjusts each speaker to obtain the same

characteristics. Select this if your speakers have

similar qualities.

Front

This adjusts each speaker to obtain the same

characteristics as the front left and right speakers.

Select this if your front left and right speakers have

significantly better qualities than the other speakers.

5 Press nCursor n to select “Start” and then

press nENTER to start the setup procedure.

A countdown starts and a measurement starts in 10

seconds. A loud test tone is output during

measurement.

Notes

• During the automatic setup procedure, do not perform any

operation on this unit.

• Press nCursor k to cancel the automatic setup procedure.

When measurement is successfully completed,

“YPAO Complete” appears on the front panel display

and the results appear on the monitor.

Displays the number of speakers connected to this unit in

the following order:

Total of Front and Center/Total of Surround and Surround

Back/Subwoofer

DIST

Displays the speaker distance from the listening position

in the following order:

Closest speaker distance/Farthest speaker distance

LVL

Displays the speaker output levels in the following order:

Lowest speaker output level/Highest speaker output level

Notes

• If “ERROR” appears on the video monitor during “Auto Setup,”

measurement is canceled and the type of error is displayed. For details,

see “When an error message is displayed during measurement”

(page 20).

• If problems occur during measurement, “WARNING (XX)” (xx indicates

the number of warning) appears above “RESULT” (see page 20).

6 Press nENTER to confirm the settings.

The speaker characteristics are adjusted according to

measurement results.

To cancel the operation, press nCursor l / h to

select “Cancel” and press nENTER.

When the following screen appears, remove the

optimizer microphone. “Auto Setup” is now

complete.

• If you do not want to apply the measurement results, select “Cancel.”

• Perform “Auto Setup” again if you change the number or positions of

speakers.

• If you press nENTER before removing the optimizer microphone,

“1 Auto Setup” of “Speaker Setup” in the setup menu (see page 41) is

displayed.

Measurement takes about 3 minutes. To obtain precise

results, stay where you will not disturb the

measurement, such as to the side of or behind the

speakers or outside the room.

1 AutoSetup

RESULT

[ENTER]:Finish

SP:3/4/0.1

DIST:2.50/3.00m

LVL:-3.5/+4.5dB

. >Set Cancel

[]/[]:Select

The optimizer microphone is sensitive to heat. Store it

in a cool place and away from direct sunlight after

measurement. Do not leave it in a place where it will be

subjected to high temperatures such on an AV

component.

1 AutoSetup

AUTOSETUPComplete

[SETUP]:Exit



DisconnectMicrophone

PRESS[ENTER]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V565 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V565

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info