Bedienungsanleitung Yamaha RX-V595aRDS (Seite 50 von 60) (Englisch)

549977

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

SETUP CODES

If you are using the DVD MENU position

for a second (or third) VCR, you must

preset the code for an LD player to the

DVD/LD position.

1. Turn on the VCR to be used.

2. Set the SELECTOR DIAL to the

CBL/DBS or DVD MENU position.

3. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

4. Press MUTE.

5. Use the numeric buttons to enter the

four-digit code for the second (or

third) VCR. Make sure that the

indicator flashes twice. If the

indicator does not flash, repeat

steps 3 and 4, and re-enter the

code.

6. Press POWER (or any other button)

on the remote control to check if you

have preset the code correctly. If

the VCR cannot be controlled with

the remote control, try entering

another code for the same manufac-

turer.

To control your components

(MD recorder, DVD player,

TV, etc.)

1. Turn on the component to be used.

2. Set the SELECTOR DIAL to the

desired position for the component

(TAPE/MD, DVD/LD, TV, etc.).

3. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

4. Use the numeric buttons to enter the

four-digit manufacturer’s code for

the component to be used. Make

sure that the indicator flashes twice.

If the indicator does not flash, repeat

step 3 and re-enter the code.

5. Press POWER (or any other button)

on the remote control to check if you

have preset the code correctly. If

the component cannot be controlled

with the remote control, try entering

another code for the same manufac-

turer.

To use a second (and third) VCR

You can use the CBL/DBS and/or DVD

MENU positions to control a second

(and/or third) VCR if a CBL (or DBS) or

DVD player is not being used.

Returning to the factory-set

codes

To return all components to the factory-

set codes, follow these steps.

1. Set the SELECTOR DIAL to a

position other than the AMP/TUN or

DSP position.

2. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

3. Enter code number “9987”.

4. Make sure that the indicator flashes

twice.

To return each component to the factory-

set code, follow these steps.

1. Set the SELECTOR DIAL to the

position for the component to be

returned to the factory-set code.

2. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

3. Enter code number “9999”.

4. Make sure that the indicator flashes

twice.

The following codes are preset as the

factory settings.

Factory-set codes

POSITION Component Code

TV TV 0037

CBL/DBS DBS tuner 2455

VCR VCR 3072

DVD/LD DVD player

4545 YAMAHA

CD CD player

6187 YAMAHA

TAPE/MD Tape deck

8524 YAMAHA

We recommend that you write all the

code numbers you have preset on the

“Quick Reference Card.”

Presetting the remote control

Perform the presetting procedure for each component you want to control with the remote control.

Note: If your component does not respond to any of the codes listed for the manufacturer, use the original remote control that was

supplied with the component.

01RX-V595aRDS-6 6/24/99, 11:02 AM50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V595aRDS Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info