Bedienungsanleitung Yamaha RX-V595RDS (Seite 53 von 67) (Englisch)

549978

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

English

SETUP CODES

To use a second (and third) VCR

You can use the CBL/DBS and/or DVD

MENU positions to control a second

VCR (and/or third) if a CBL (or DBS) or

DVD player is not used.

If you are using the DVD MENU position

for a second (or third) VCR, you must

preset a code for an LD player to the

DVD/LD position.

1. Turn on the VCR to be used.

2. Set the SELECTOR DIAL to the

CBL/DBS or DVD MENU position.

3. Press both VOLUME buttons (

) at the same time until the

indicator flashes twice.

4. Press MUTE.

5. Use the numeric buttons to enter the

four-digit code for a second (or third)

VCR. Make sure that the indicator

flashes twice. If the indicator does

not flash, repeat step 3 and 4, and

re-enter the code.

To control your components

(MD recorder, DVD player,

TV etc.)

1. Turn on the component to be used.

2. Set the SELECTOR DIAL to the

desired component (TAPE/MD,

DVD/LD, TV etc.).

3. Press both VOLUME buttons (

) at the same time until the

indicator flashes twice.

4. Use the numeric buttons to enter the

four-digit manufacturer’s code for

the component to be used. Make

sure that the indicator flashes twice.

If the indicator does not flash, repeat

step 3 and re-enter the code.

5. Press POWER (or any other button)

on the remote control transmitter to

check if you have preset the code

correctly. If the component cannot

be controlled using the remote

control transmitter, try entering

another code for the same manufac-

turer.

6. Press POWER (or any other button)

on the remote control transmitter to

check if you have preset the code

correctly. If the VCR cannot be

controlled using the remote control

transmitter, try entering another

code for the same manufacturer.

Returning to the default code

To return all components to the default

code, follow these steps.

1. Press both VOLUME buttons (

) at the same time until the

indicator flashes twice.

2. Enter the code number “9987”.

3. Make sure that the indicator flashes

twice.

To return each component to the default

code, follow these steps.

1. Set the SELECTOR DIAL to the

component to be return to the

default code.

2. Press both VOLUME buttons (

) at the same time until the

indicator flashes twice.

3. Enter the code number “9999”.

4. Make sure that the indicator flashes

twice.

The following codes are preset as the

default code.

Default codes

POSITION Component Code

TV TV 0037

CBL/DBS DBS tuner 2455

VCR VCR 3072

DVD/LD DVD player

4545 YAMAHA

CD CD player

6187 YAMAHA

TAPE/MD Tape deck

8524 YAMAHA

We recommend that you write all code

numbers you have preset on the “Quick

Reference Card”.

Presetting the remote control transmitter

Perform the presetting procedure for each component you want to control with this remote control transmitter.

Note: If your component does not respond to any of the codes listed for the manufacturer, use the original remote control that

came with the component.

01RX-V595RDS-6 6/23/99, 1:14 PM53

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V595RDS Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info