Bedienungsanleitung Yamaha RX-V659 (Seite 14 von 128) (Englisch)

464162

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

CONNECTIONS

The speaker layout below shows the standard ITU-R

speaker setting. You can use it to enjoy CINEMA DSP and

multi-channel audio sources.

ITU-R is the radio communication sector of the ITU

(International Telecommunication Union).

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers at an equal distance

from the ideal listening position. The distance of each

speaker from each side of the video monitor should be the

same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system. Place the

center speaker centrally between the front speakers and as

close to the monitor as possible, such as directly over or

under it.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds. Place these speakers behind your listening

position, facing slightly inwards, about 1.8 m above the

floor.

Surround back left and right speakers

(SBL and SBR)

The surround back speakers supplement the surround

speakers and provides more realistic front-to-back

transitions. Place these speakers directly behind the

listening position and at the same height as the surround

speakers. They should be positioned at least 30 cm apart.

Ideally, they should be positioned at the same width as that

of the front speakers.

Presence left and right speakers (PL and PR)

The presence speakers supplement the sound from the

front speakers with extra ambient effects produced by

CINEMA DSP (see page 64). These effects include

sounds that filmmakers intent to locate a little farther back

behind the screen in order to create more theater-like

ambience. Place these speakers at the front of the room

about 0.5 – 1 m outside the front speakers, facing slightly

inward, and about 1.8 m above the floor.

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as

the YAMAHA Active Servo Processing Subwoofer

System, is effective not only for reinforcing bass

frequencies from any or all channels, but also for hi-fi

stereo sound reproduction of the LFE (low-frequency

effect) channel included in Dolby Digital and DTS

sources. The position of the subwoofer is not so critical,

because low bass sounds are not highly directional. But it

is better to place the subwoofer near the front speakers.

Turn it slightly toward the center of the room to reduce

wall reflections.

CONNECTIONS

Placing speakers

SBR

SBL

60˚

30˚

SBR

SBL

80˚

1.8 m

30 cm (12 in) or more

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V659 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V659

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info