Bedienungsanleitung Yamaha RX-V740 (Seite 18 von 68) (Englisch)

559127

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

■ Connections

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) in accordance with the markers on

this unit, the speakers, and the speaker cables. If the connections are faulty, no sound will be heard from the speakers,

and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit

and/or the speakers.

10 mm (3/8”)

Red: positive (+)

Black: negative (–)

Banana plug

(With the exception of U.K. and Europe models)

CONNECTIONS

A speaker cord is actually a pair of insulated cables

running side by side. One cable is colored or shaped

differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

3 Unscrew the knob.

4 Insert one bare wire into the hole in the side

of each terminal.

5 Tighten the knob to secure the wire.

(With the exception of U.K. and Europe models)

• You can also use banana plug connectors. First, tighten the

knob and then insert the banana plug connector into the end of

the corresponding terminal.

MAIN

CENTER

REAR CENTER

REAR

A OR B :

A+B :

4ΩMIN.

8ΩMIN.

6ΩMIN.

/SPEAKER

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN

CENTER

REAR CENTER

REAR

A OR B :

A+B :

8ΩMIN.

16ΩMIN.

8ΩMIN.

/SPEAKER

■ IMPEDANCE SELECTOR switch

WARNING

Do not change setting of the IMPEDANCE SELECTOR switch when the unit power is switched on, as doing so may

damage the unit. If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the

IMPEDANCE SELECTOR switch may not be fully slid to either position. If this is the case, slide the switch all the

way to either position when this unit is in standby mode. Be sure to move this switch only when this unit is in

standby mode.

Select the switch position (left or right) according to the impedance of the speakers in your system.

IMPEDANCE SELECTOR

switch

(General model)

Switch

position

Left

Right

Speaker

Main

Center,

Rear Center,

Rear

Main*

Center,

Rear Center,

Rear

Impedance level

If you use one/two set(s) of main speakers, the impedance of

each speaker must be 4 Ω/8 Ω or higher.

The impedance of each speaker must be 6 Ω or higher.

If you use one/two set(s) of main speakers, the impedance of

each speaker must be 8 Ω/16 Ω or higher.

The impedance of each speaker must be 8 Ω or higher.

* [Canada model only]

When the switch is set to right, you cannot use “A+B”.

0103RX-V740_09-19_EN-GB.p65 03.2.12, 4:23 PM16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V740 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V740

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info