Bedienungsanleitung Yamaha S90 (Seite 14 von 139) (Englisch)

587006

Zoom out

Zoom in

Vorherige Seite

1/139

Nächste Seite

Basics Section Quick Guide Reference Appendix

Setting Up

Power Supply

Make sure the POWER switch on the S90 is set to OFF.

2Connect the supplied power cord to the AC INLET

terminal on the instrument’s rear panel.

3Connect the other end of the power cord to an AC

outlet. Make sure your S90 meets the voltage

requirement for the country or region in which it is

being used.

Make sure your S90 is rated for the AC voltage supplied

in the area in which it is to be used (as listed on the rear

panel). Connecting the unit to the wrong AC supply can

cause serious damage to the internal circuitry and may

even pose a shock hazard!

Use only the AC power cord supplied with the S90. If

the supplied cord is lost or damaged and needs to be

replaced, contact your Yamaha dealer. The use of an

inappropriate replacement can pose a ﬁre and shock

hazard!

The type of AC power cord provided with the S90 may be

different depending on the country in which it is

purchased (a third prong may be provided for grounding

purposes). Improper connection of the grounding

conductor can create the risk of electrical shock.

Do NOT modify the plug provided with the S90. If the

plug will not ﬁt the outlet, have a proper outlet installed

by a qualiﬁed electrician. Do not use a plug adapter

which defeats the grounding conductor.

Power-on Procedure

Once you’ve made all the necessary connections (page

15) between your S90 and any other devices, make

sure that all volume settings are turned down all the

way to zero. Then, turn on the every device in your

setup in the order of MIDI masters (senders), MIDI

slaves (receivers), then audio equipment (mixers,

ampliﬁers, speakers, etc.). This ensures smooth signal

ﬂow from the ﬁrst device to the last (ﬁrst MIDI, then

audio). When powering down the setup, ﬁrst turn

down the volume for each audio devices, then switch

off each device in the reverse order (ﬁrst audio devices,

then MIDI).

When using the S90 as MIDI receiver:

Turning on the S90

Before you switch your S90 on or off, ﬁrst turn down the

volume of any connected audio equipment.

1Press the POWER switch.

After a while, the default display appears (as set in

the Utility parameter, Power On Mode Display).

nAdjusting the display contrast if the LCD is difﬁcult

to read, adjust the contrast with the LCD contrast

control knob (page 12).

2Raise the sound system volume to a reasonable

level.

3Gradually raise the MASTER VOLUME control

while playing the keyboard to set the desired

listening level.

AC INLET terminal

Power cord

(included)

12345678910111213141516LR

MUSIC SYNTHESIZER

Modular Synthesis Plug-in System

MIDI master (transmitting device)

S90 as MIDI slave (MIDI receiving device)

Audio equipment (ﬁrst mixer, then ampliﬁer)

POWER

ON!

AC INLET

POWER

ON/ OFF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha S90 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha S90

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info