Bedienungsanleitung Yamaha S90 (Seite 120 von 139) (Englisch)

587006

120

Zoom out

Zoom in

Vorherige Seite

1/139

Nächste Seite

120

Basics Section Quick Guide Reference Appendix

About MIDI

Sostenuto (Control #066)

Messages which control sostenuto on/off.

Holding speciﬁc notes and then pressing and holding the

sostenuto pedal will sustain those notes as you play

subsequent notes, until the pedal is released.

Setting the value between 64 -127 turns the sostenuto on,

between 0 - 63 turns the sostenuto off.

Harmonic Content (Control #071)

Messages which adjust the ﬁlter resonance set for each

Part.

The value set here is an offset value which will be added

to or subtracted from the voice data.

Higher values will result in a more characteristic,

resonant sound.

Depending on the voice, the effective range may be

narrower than the range available for adjustment.

Release Time (Control #072)

Messages which adjust the AEG release time set for each

Part.

The value set here is an offset value which will be added

to or subtracted from the voice data.

Attack Time (Control #073)

Messages which adjust the AEG attack time set for each

Part.

The value set here is an offset value which will be added

to or subtracted from the voice data.

Brightness (Control #074)

Messages which adjust the ﬁlter cutoff frequency set for

each Part.

The value set here is an offset value which will be added

to or subtracted from the voice data.

Lower values will result in a softer sound.

Depending on the voice, the effective range may be

narrower than the range available for adjustment.

Decay Time (Control #075)

Messages which adjust the AEG decay time set for each

Part. The value set here is an offset value which will be

added to or subtracted from the voice data.

Effect1 Depth (Reverb Send Level)

(Control #091)

Messages which adjust the send level for the Reverb effect.

Effect3 Depth (Chorus Send Level)

(Control #093)

Messages which adjust the send level for the Chorus effect.

Data Increment (Control #096)

Decrement (Control #097) for RPN

Messages which increase or decrease the MSB value of

pitch bend sensitivity, ﬁne tune, or coarse tune in steps of

1. You are required to assign one of those parameters

using the RPN in the external device in advance.

The data byte is ignored.

When the maximum value or minimum value is reached,

the value will not be incremented or decremented further.

(Incrementing the ﬁne tune will not cause the coarse

tune to be incremented.)

NRPN (Non-Registered Parameter Number)

LSB (Control #098) (Plug-in Board only)

NRPN (Non-Registered Parameter Number)

MSB (Control #099) (Plug-in Board only)

Messages which adjust a voice’s vibrato, ﬁlter, EG, drum

setup or other parameter settings.

First send the NRPN MSB and NRPN LSB to specify the

parameter which is to be controlled. Then use Data Entry

(page 119) to set the value of the speciﬁed parameter.

Note that once the NRPN has been set for a channel,

subsequent data entry will be recognized as the same

NRPN’s value change. Therefore, after you use the

NRPN, you should set a Null (7FH, 7FH) value to avoid

an unexpected result.

For details, refer to the owner’s manual of the relevant

Plug-in Board.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha S90 Seite 120

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha S90

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info