689860
16
Zoom out
Zoom in
Vorherige Seite
1/363
Nächste Seite
Maintenance techniques, tools and working facilities
0-15
Maintenance and minor repair tool kit
The tools in this list should be considered the minimum required
for performance of routine maintenance, servicing and minor repair
work. We recommend the purchase of combination wrenches (box end
and open end combined in one wrench); while more expensive than
open-ended ones, they offer the advantages of both types of wrench.
Combination wrench set (6 mm to 22 mm)
Adjustable wrench -8 in
Spark plug socket (with rubber insert)
Spark plug gap adjusting tool
Feeler gauge set
Standard screwdriver (5/16 in x 6 in)
Phillips screwdriver (No. 2x6 in)
Allen (hex) wrench set (4 mm to 12 mm)
Combination (slip-joint) pliers - 6 in
Hacksaw and assortment of blades
Tire pressure gauge
Control cable pressure luber
Grease gun
Oil can
Fine emery cloth
Wire brush
Hand impact screwdriver and bits
Funnel (medium size)
Safety goggles
Drain pan
Work light with extension cord
Repair and overhaul tool set
These tools are essential for anyone who plans to perform major
repairs and are intended to supplement those in the Maintenance and
minor repair tool kit. Included is a comprehensive set of sockets which,
though expensive, are invaluable because of their versatility (especially
when various extensions and drives are available). We recommend the
3/8 inch drive over the 1/2 inch drive for general motorcycle
maintenance and repair (ideally, the mechanic would have a 3/8 inch
drive set and a 1/2 inch drive set).
Socket set(s)
Reversible ratchet
Extension - 6 in
Universal joint
Torque wrench (same size drive as sockets)
Ball pein hammer - 8 oz
Soft-faced hammer (plastic/rubber)
Standard screwdriver (1/4 in x 6 in)
Standard screwdriver (stubby - 5/16 in)
Phillips screwdriver (No. 3x8 in)
Phillips screwdriver (stubby - No. 2)
Pliers - locking
Pliers - lineman's
Pliers - needle nose
Pliers - snap-ring (internal and external)
Cold chisel - 1/2 in
Scriber
Scraper (made from flattened copper tubing)
Center punch
Pin punches (1/16, 1/8, 3/16 in)
Steel rule/straightedge - 12 in
Pin-type spanner wrench
A selection of files
Wire brush (large)
Note: Another tool which is often useful is an electric drill with a chuck
capacity of 3/8 inch (and a set of good quality drill bits).
Special tools
The tools in this list include those which are not used regularly,
are expensive to buy, or which need to be used in accordance with
their manufacturer's instructions. Unless these tools will be used
frequently, it is not very economical to purchase many of them. A
consideration would be to split the cost and use between yourself and
a friend or friends (i.e. members of a motorcycle club).
This list primarily contains tools and instruments widely available
to the public, as well as some special tools produced by the vehicle
manufacturer for distribution to dealer service departments. As a
result, references to the manufacturer's special tools are occasionally
included in the text of this manual. Generally, an alternative method of
doing the job without the special tool is offered. However, sometimes
there is no alternative to their use. Where this is the case, and the tool
can't be purchased or borrowed, the work should be turned over to the
dealer service department or a motorcycle repair shop.
Valve spring compressor
Piston ring removal and installation tool
Piston pin puller
Telescoping gauges
Micrometers) and/or dial/Vernier calipers
Cylinder surfacing hone
Cylinder compression gauge
Dial indicator set
Multimeter
Adjustable spanner
Manometer or vacuum gauge set
Small air compressor with blow gun and tire chuck
Buying tools
For the do-it-yourselfer who is just starting to get involved in
motorcycle maintenance and repair, there are a number of options
available when purchasing tools. If maintenance and minor repair is the
extent of the work to be done, the purchase of individual tools is
satisfactory. If, on the other hand, extensive work is planned, it would
be a good idea to purchase a modest tool set from one of the large
retail chain stores. A set can usually be bought at a substantial savings
over the individual tool prices (and they often come with a tool box). As
additional tools are needed, add-on sets, individual tools and a larger
tool box can be purchased to expand the tool selection. Building a tool
set gradually allows the cost of the tools to be spread over a longer
period of time and gives the mechanic the freedom to choose only
those tools that will actually be used.
Tool stores and motorcycle dealers will often be the only source
of some of the special tools that are needed, but regardless of where
tools are bought, try to avoid cheap ones (especially when buying
screwdrivers and sockets) because they won't last very long.There are
plenty of tools around at reasonable prices, but always aim to
purchase items which meet the relevant national safety standards. The
expense involved in replacing cheap tools will eventually be greater
than the initial cost of quality tools.
It is obviously not possible to cover the subject of tools fully here.
For those who wish to learn more about tools and their use, there is a
book entitled Motorcycle Workshop Practice Manual (Book no. 1454)
available from the publishers of this manual. It also provides an
introduction to basic workshop practice which will be of interest to a
home mechanic working on any type of motorcycle.
Care and maintenance of tools
Good tools are expensive, so it makes sense to treat them with
respect. Keep them clean and in usable condition and store them
properly when not in use. Always wipe off any dirt, grease or metal
chips before putting them away. Never leave tools lying around in the
work area.
Some tools, such as screwdrivers, pliers, wrenches and sockets,
can be hung on a panel mounted on the garage or workshop wall,
while others should be kept in a tool box or tray. Measuring
instruments, gauges, meters, etc. must be carefully stored where they
can't be damaged by weather or impact from other tools.
When tools are used with care and stored properly, they will last a
very long time. Even with the best of care, tools will wear out if used
frequently. When a tool is damaged or worn out, replace it; subsequent
jobs will be safer and more enjoyable if you do.
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

yamaha-xv750-virago

Suche zurücksetzen

  • Für was ist die Kontrollleuchte im Tacho öl oder Benzin Eingereicht am 23-7-2023 18:17

    Antworten Frage melden
  • bei einer vz 750 1997 ist in der sissibar eine verkromte box , abschliesbar . was ist das ,und was ist da drinnen oder kommt da rein ??? Eingereicht am 19-3-2022 16:02

    Antworten Frage melden
  • Im Drehzahlmesser leuchtet eine rote LAmpe mit der Bezeicchnung Fuel auf. Ist das vielleicht diE Tankanzeige?
    Wer kann helfen?
    Danke und Gruß Andi Eingereicht am 9-9-2021 18:21

    Antworten Frage melden
  • Wie öffnet man den Tacho an der XV 750 zum Wechseln der Birne Eingereicht am 17-9-2020 15:30

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha XV750 Virago wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info