Bedienungsanleitung Yamaha XV920 Virago (Seite 315 von 363) (Englisch)

689861

315

Zoom out

Zoom in

Vorherige Seite

1/363

Nächste Seite

8A-12

Chapter 8 Part A Electrical system (XV535 models)

19.5 Sidestand switch mounting screws 20.4 Insert a pointed tool into the hole

(arrow), compress the prong and pull out

the clutch switch

21.1 Disconnect the horn wires (A) and

remove the bracket bolt (B)"

3 With the sidestand in the down position, the meter should

indicate infinite resistance.

4 If the switch fails either of these tests, replace it.

Replacement

Refer to illustration 19.5

5 With the sidestand in the up position, unscrew the two screws

and remove the switch (see illustration). Disconnect the switch

electrical connector.

6 Installation is the reverse of the removal procedure.

20 Clutch switch - check and replacement

Check

1 Disconnect the electrical connector from the clutch switch.

2 Connect an ohmmeter between the terminals in the clutch switch.

With the clutch lever pulled in, the ohmmeter should show continuity

(little or no resistance). With the lever out, the ohmmeter should show

infinite resistance.

3 If the switch doesn't check out as described, leplace it.

Replacement

Refer to illustration 20.4

4 If you haven't already done so. disconnect the wiring connector.

Insert a pointed tool into the mounting hole, compress the prong and

pull the switch out (see illustration).

5 Installation is the reverse of removal.

21 Horn - check and replacement

Check

Refer to illustration 21.1

1 Disconnect the electrical connectors from the horn (see

illustration). Using two jumper wires, apply^battery voltage directly to

the terminals on the horn. If the horn sounds, check the switch (see

Section 17) and the wiring between the switch and the horn (see the

wiring diagrams at the end of this Chapter).

2 If the horn doesn't sound, replace it.

Replacement

3 Unbolt the horn bracket from the frame (see illustration 21.1) and

detach the electrical connectors.

22.4 Disconnect the cable that runs to the starter

A Cable to starter

B Cable from battery positive terminal

C Two-wire connector

4 Unbolt the horn from the bracket and transfer the bracket to the

new horn.

5 Installation is the reverse of removal.

22 Starter relay - check and replacement

Refer to illustration 22.4

Check

1 Remove the seat (see Chapter 7). Disconnect the battery negative

cable.

2 Make sure the battery is fully charged and the relay wiring

connections are clean and tight. Corrosion can build up enough to

prevent current flow and still not be readily visible, so it's best to

disconnect the cables from the terminals and give the cable ends and

terminal studs a thorough cleaning. Also disconnect the two-wire

connectors and clean the terminals.

3 Reconnect the wires to the starter relay.

4 Warning: Make sure the transmission is in neutral for this step.

Pull back the protective cover and disconnect the cable that runs from

the relay to the starter motor (see illustration). Connect a heavy-

gauge jumper wire (the same gauge or heavier than the starter relay

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha XV920 Virago Seite 315

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info