Bedienungsanleitung Yamaha YDP-140 (Seite 13 von 44) (Englisch)

599659

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Before Using the Digital Piano

YDP-160/140 Owner’s Manual

Connecting the Power Cord (YDP-160)

Read the instructions below very carefully to make sure that you correctly connect the power cord. YDP-140 users should

skip to the next section “Connecting the Power Adaptor (YDP-140)” for information on connecting the power adaptor.

1. Insert the plug on one end of the power cord to the [AC IN] connector. Refer to the “Part Names and

Functions” on page 11 for information on the location of the [AC IN] connector.

2. Insert the plug on the other end of the power cord to a standard AC outlet.

(The shape of the plug differs depending on locale.)

WARNING

Make sure your digital piano is rated for the AC voltage supplied in the area in which the piano will be used. (The voltage rating appears

on the name plate on the bottom panel). In some areas, a voltage selector may be provided on the bottom panel of the main keyboard

unit near the power cord. Make sure that the voltage selector is set for the voltage in your area. Connecting the unit to an inappropriate

AC supply can seriously damage the internal circuitry and may even pose a shock hazard!

Use only the AC power cord supplied with the instrument. If the supplied power cord is lost or damaged and needs to be replaced, contact

your Yamaha dealer. The use of an inappropriate replacement can pose a ﬁre and shock hazard!

The type of AC power cord provided with the instrument may be different depending on the country in which the instrument was pur-

chased. (In some areas a plug adaptor may be provided to match the pin conﬁguration of the AC wall outlets in your area.)

Do NOT modify the plug provided with the instrument. If the plug will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electri-

cian.

Connecting the Power Adaptor (YDP-140)

Read the instructions below very carefully to make sure that you correctly connect the power adaptor. YDP-160 users

should skip back to the previous section “Connecting the Power Cable (YDP-160)” for information on connecting the

power cord.

1. Make sure that the [STANDBY/ON] switch is set to STANDBY.

2. Connect the DC plug of the power adaptor into the [DC IN 12V] connector. Refer to the “Part Names

and Functions” on page 11 for more information on the location of the [DC IN 12V] connector. Loop

cord slack onto the cord hook so that the plug will not be disconnected accidentally.

3. Insert the AC plug of the power adaptor into a standard AC outlet.

WARNING

Be sure to use a speciﬁed power adaptor. Using a different power adaptor may cause malfunction, overheating, or ﬁre.

WARNING

Do not bend the cord tightly when you hang the cord on the cord hook. Otherwise, a short-circuit or ﬁre may result.

WARNING

Be sure to use an appropriate AC outlet.

CAUTION

If you plan not to use the instrument for a long period of time, or if there is a possibility of lightning, be sure to remove

the power cord plug from the AC outlet.

(Bottom of the

keyboard)

(Bottom of the keyboard)

Cord hook

Adaptor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha YDP-140 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha YDP-140

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info